Skip to content
Omnikalc

Angle of repose calculator: how tall and heavy is your pile?

Enter the angle of repose, the base diameter and the bulk density to get the height, the volume in cubic feet and yards, the weight and the slope of a conical pile of loose material.

Updated on
Your inputs
°

Value out of range

Value out of range

Value out of range

Results

Height of the pile

6.75 ft

Volume of the pile (cubic feet)
706 ft³
Volume of the pile (cubic yards)
26.2 yd³
Weight of the pile (short tons)
35.3 tons
Slope run for each unit of rise
1.48 :1

Loose material poured into a heap forms a cone with a fixed slope. The angle of repose calculator takes the angle of repose, the base diameter of the pile and the bulk density of the material and gives the height of the pile, its volume in cubic feet and cubic yards, its weight in short tons and the slope run for each unit of rise.

How the calculation works

  • Height of a conical pile = radius × tan(angle of repose). The radius is half the base diameter.
  • Volume = π × radius² × height ÷ 3, the volume of a cone.
  • Weight = volume × bulk density. A short ton is 2 000 pounds.
  • Slope run = 1 ÷ tan(angle of repose). At 34° the pile spreads 1.48 ft sideways for each foot of height.

Example

A pile of dry sand has an angle of repose of 34°, a base 20 ft across, and a bulk density of 100 lb/ft³. The radius is 10 ft, so the height is 10 × tan 34° = 6.75 ft. The volume is π × 10² × 6.75 ÷ 3 = 706 ft³, which is 26.2 yd³, and the pile weighs 706 × 100 = 70 600 lb, or 35.3 tons.

Why it matters

Stockpiles of sand, gravel, topsoil, grain or mulch need space and stable footing. The calculator tells you the footprint required for a given volume, the height a loader can reach, and the weight on the ground or on a truck, which helps with orders and delivery.

Good to know

A real pile is rarely a perfect cone, since it is built by tipping from a truck or a conveyor, and the sides vary with moisture. The angle of repose depends on the material and its condition, so use a value measured for yours. The bulk density also changes with moisture and compaction, and wet sand weighs about 20 percent more than dry sand.

The gravel calculator sizes a load of stone for a surface and the sandbox calculator tells you how much sand to order for a play area.

Frequently asked questions

What is the angle of repose?

It is the steepest angle at which a pile of loose material stays stable when it is poured freely onto a flat surface. Above this angle, the material slides. It depends on the size, shape and moisture of the grains, and on how rough they are.

What value should I use for sand and gravel?

Dry sand is about 30 to 35 degrees, and gravel about 30 to 40 degrees. Crushed stone with sharp edges can reach 40 or more because the grains lock together. Wet sand holds a steeper pile, up to 45 degrees, until it dries or becomes saturated. If in doubt, measure a small pile.

How do I measure it?

Pour the material through a funnel onto a flat surface, so it forms a cone. Measure the height h and the base radius r of the cone, and the angle is the arctangent of h divided by r. Repeat several times and average the results, since the pile varies.

Does the angle of repose give a safe slope for an excavation?

No. A cut face in soil can stand steeper than the angle of repose because of cohesion, and it can also collapse suddenly. Safe excavation slopes are set by local safety rules and a competent person, and they are not the same as the angle of repose of a loose pile.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.