Skip to content
Omnikalc

Roof underlayment and ice barrier rolls calculator

Enter the pitch, the eave, the slope, the overhang and the size of the rolls to get the width of the ice barrier, the areas and the number of rolls of each.

Updated on
Your inputs

Value out of range

ft

Value out of range

ft

Value out of range

Value out of range

ft

Value out of range

ft

Value out of range

ft²

Value out of range

ft²

Value out of range

%

Value out of range

Results

Rolls of ice barrier

3

Rolls of underlayment

3

Width of the ice barrier along the slope
3.91 ft
Area of the ice barrier
469.6 ft²
Total roof area
2,400 ft²
Area of the underlayment
1,930.4 ft²

The roof underlayment and ice barrier calculator gives the width of the ice barrier along the slope, its area, the area of the underlayment and the number of rolls of each, from the pitch, the eave, the length of the slope, the overhang and the size of the rolls.

How the calculation works

  • Enter the pitch, the length of the eave, the length of the slope and the number of slopes.
  • Enter the eave overhang, the thickness of the wall, the area of the rolls and the waste.
  • The calculator finds the width of the ice barrier, the areas and the number of rolls of ice barrier and of underlayment.

Example

A roof of 2 slopes with an eave of 60 ft, a slope of 20 ft and a pitch of 6 in 12 has an area of 60 × 20 × 2 = 2,400 ft². With an overhang of 1 ft and a wall of 0.5 ft, the ice barrier must reach 24 in inside the wall line, that is (1 + 0.5 + 2) × 1.118 = 3.91 ft along the slope. Its area is 469.6 ft², and the underlayment covers the remaining 1,930.4 ft². With 10 percent of waste, the job needs 3 rolls of ice barrier of 200 ft² and 3 rolls of underlayment of 1,000 ft².

Why it matters

The calculator helps roofers, builders, homeowners and estimators to order the right quantity of ice barrier and underlayment before the work starts, to see how much of the roof is covered by the more expensive ice barrier, and to compare the cost of the two membranes.

Good to know

Start the ice barrier at the eave, with the top of the first sheet laid flat against the sheathing, and lap each sheet by 3 to 6 in. Extend it up the valleys and around the penetrations. Apply the barrier when the roof deck is dry, clean and above 40 °F, and lay the underlayment with the laps shingled so that the water runs over them. Roll sizes vary, so check the real area on the label.

The roof replacement cost calculator gives the total cost of a new roof, the roof calculator gives the area of a roof from its dimensions, the metal roof panels calculator gives the number of panels and the roof battens calculator gives the number of battens.

Frequently asked questions

How wide must the ice barrier be?

Building codes in cold regions require a self-adhering ice barrier from the edge of the roof to a point at least 24 in inside the exterior wall line, measured horizontally. The width along the slope is therefore the overhang, plus the thickness of the wall, plus 24 in, divided by the cosine of the angle of the roof. On a steeper roof the width along the slope is larger for the same horizontal distance.

What is the difference between the ice barrier and the underlayment?

The ice barrier is a self-adhering membrane of modified bitumen that seals around the nails and stops the water pushed back under the shingles by an ice dam. The underlayment is a felt or synthetic sheet that covers the rest of the roof as a second layer of protection against wind-driven rain. The calculator gives the area of each, because their prices and their roll sizes are very different.

How much waste should I allow?

Allow about 10 percent for a simple gable roof and 15 percent or more for a roof with hips, valleys, dormers and chimneys. The rolls also have laps of 3 to 6 in at the ends and at the sides, which the waste includes. Round the number of rolls up, because a partial roll cannot be bought, and keep the leftover pieces for the flashings.

What does the calculator leave out?

The calculator takes each slope as a rectangle with the same eave length. It does not include the valleys, which need a wider strip of ice barrier, the walls that meet a roof, the skylights, the low-slope areas that need a different membrane, the ridge or the rakes. Add these areas by hand and check the requirement of the local code.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.