Skip to content
Omnikalc

How long should a swale be?

Enter the area draining to the swale, the design rainfall, the runoff coefficient, the swale top width and depth and the soil infiltration rate: get the runoff volume, the swale length to hold it and the time it takes to drain.

Updated on
Your inputs
sq ft

Value out of range

in

Value out of range

%

Value out of range

ft

Value out of range

ft

Value out of range

in/h

Value out of range

Results

Runoff volume

150 cu ft

Swale length to hold it

56 ft

Runoff in gallons
1,122 gal
Swale cross-section area
2.67 sq ft
Time to drain
24 h
Test infiltration by filling a hole with water; keep swales at least 10 ft from foundations and check local stormwater rules

A swale is a shallow, vegetated channel that collects runoff from roofs, driveways or lawns and lets it soak into the ground instead of flooding the yard or overloading storm drains. Sizing one means estimating how much water a storm sends to it, giving the swale enough volume to hold that water, and checking that it drains in time.

How the calculation works

  • Runoff volume = area draining to the swale × design rainfall × runoff coefficient
  • Swale cross-section = 2/3 × top width × depth, for a gently rounded (parabolic) shape
  • Length needed = runoff volume ÷ cross-section area
  • Time to drain = depth ÷ soil infiltration rate

1 in of rain on 2,000 sq ft of roof with a runoff coefficient of 90% sends about 150 cu ft of water, or 1,122 gallons. A swale 4 ft wide and 1 ft deep holds about 2.67 sq ft per foot of length, so it needs to be about 56 ft long. At an infiltration rate of 0.5 in per hour, it drains in about 24 hours.

Runoff coefficients

Surface Typical runoff coefficient
Metal or shingle roof 90 to 95%
Asphalt or concrete 85 to 95%
Gravel 30 to 60%
Lawn on clay soil 20 to 35%
Lawn on sandy soil 5 to 15%

Infiltration rates

Soil Typical rate
Sand 1 in per hour or more
Loam 0.5 to 1 in per hour
Silt loam 0.25 to 0.5 in per hour
Clay under 0.1 in per hour

To test your soil, dig a hole about 12 in deep, fill it with water, let it drain, refill it and measure how fast the level drops. If water stays more than 48 hours, use a shallower swale, add a gravel trench under it or choose a rain garden with amended soil.

Building a swale

  • Follow the contour of the land, or give it a very gentle slope so water spreads and slows.
  • Keep it at least 10 ft from foundations and away from septic fields and steep slopes.
  • Plant the bottom and sides with deep-rooted grasses or native plants that tolerate both wet and dry spells.
  • Add an overflow to a safe place for storms bigger than the design rain.

Rules

Many towns have stormwater rules for new impervious areas, and some offer rebates for swales and rain gardens. Call before you dig to locate buried utilities.

Frequently asked questions

How much runoff does 1 in of rain make on 2,000 sq ft of roof?

About 150 cu ft, or 1,122 gallons, with a 90% runoff coefficient.

How long should a swale be?

About 56 ft for 150 cu ft of runoff in a swale 4 ft wide and 1 ft deep.

How fast should a swale drain?

Within 24 to 48 hours; longer standing water can breed mosquitoes.

How far should a swale be from a house?

At least 10 ft from foundations, and away from septic systems.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.