Skip to content
Omnikalc

Yellow light duration calculator: yellow, all-red and total change interval

Enter the approach speed, the reaction time, the deceleration, the grade and the intersection width to get the yellow interval, the all-red interval and the total change interval of a traffic signal.

Updated on
Your inputs
mph

Value out of range

s

Value out of range

ft/s²

Value out of range

%

Value out of range

ft

Value out of range

ft

Value out of range

Results

Yellow interval

3.57 s

Within the usual range of 3 to 6 s
All-red interval
1.56 s
Total change interval
5.13 s
Approach speed
51.33 ft/s

The yellow light warns drivers that the signal will turn red, and the all-red interval clears the intersection. The yellow light duration calculator gives the yellow interval, the all-red interval and the total change interval of a traffic signal, with the ITE formula, from the speed, the grade and the width of the intersection.

How the calculation works

  • Enter the approach speed (the speed limit or the 85th percentile speed) and the perception-reaction time of the driver, usually 1 s.
  • Enter the comfortable deceleration (10 ft/s² is the usual value of the ITE) and the grade of the approach.
  • Enter the width of the intersection and the length of a vehicle, for the all-red interval.
  • The calculator applies the ITE formula y = t + v / (2a + 2Gg) for the yellow interval and (w + L) / v for the all-red interval.

Example

An approach has a speed of 35 mph (51.3 ft/s), a reaction time of 1 s, a deceleration of 10 ft/s² and a flat grade. The yellow interval is 1 + 51.33 / (2 × 10) = 3.57 s. For an intersection of 60 ft and a vehicle of 20 ft, the all-red interval is (60 + 20) / 51.33 = 1.56 s. The total change interval between the green and the conflicting green is 5.13 s.

Why it matters

The calculator helps traffic engineers, students, city staff and curious drivers to check the length of a yellow light, to see how the speed and the grade change it, and to understand why a short yellow causes dilemma zone problems. It gives the base values for a timing study.

Good to know

Use the speed measured on the approach, not only the speed limit: the 85th percentile speed is often higher. Round the yellow up to the next tenth of a second. Check the all-red interval with the width measured from the stop line to the far edge of the last conflicting lane, and consider the pedestrian crossing time.

The stopping distance calculator gives the distance to stop, the speed distance time calculator converts speeds, the acceleration calculator covers the deceleration, and the queue wait time calculator estimates the delay at a signal.

Frequently asked questions

How is the yellow interval computed?

The ITE formula is y = t + v / (2a + 2Gg), where t is the perception-reaction time (about 1 s), v the approach speed, a the comfortable deceleration (10 ft/s² or 3.0 m/s²), G the grade as a ratio and g the gravity. The first term is the time to react, and the second the time to stop. A driver who can neither stop comfortably nor clear the intersection would be in the dilemma zone, which the interval is meant to remove.

What is the all-red interval?

The all-red interval is the time when all the signals of the intersection are red, after the yellow, to let a vehicle that entered at the end of the yellow clear the intersection before the conflicting traffic gets the green. It is (w + L) / v, with w the distance from the stop line to the far side of the conflict zone and L the length of the vehicle. Many agencies limit it or reduce it for the speed at which a vehicle enters.

What are the usual limits?

Most agencies use a minimum yellow of 3 s and a maximum of about 5 to 6 s. A very short yellow causes red-light running and rear-end crashes, and a very long one is taken as a green and reduces the respect of the signal. Higher approach speeds, uphill grades reduce, and downhill grades increase the time needed to stop.

Is this an official signal design?

No. It is the standard formula for a first estimate. A signal timing must follow the local manual, such as the MUTCD in the United States, take the local speed data and the features of the intersection into account, and be approved by the traffic authority. Never change the timing of a real signal without authorization.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.