Skip to content
Omnikalc

Crop water requirement calculator: how much should I irrigate?

Enter ET0, the crop coefficient, the area, the efficiency of your system and the rain to get the crop water use and the gallons or litres to apply each day and week.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

%

Value out of range

Value out of range

Results

Water to apply per day

374 gal

Crop water use ETc
0.28 in/day
Gross irrigation need per day
0.30 in/day
Water to apply per week
2,618 gal

Knowing how much to water is the main question of irrigation. The crop water requirement calculator takes the reference evapotranspiration, the crop coefficient, the irrigated area, the irrigation efficiency and the effective rain and gives the crop water use, the gross irrigation need, and the volume of water to apply per day and per week.

How the calculation works

  • Crop water use ETc = ET₀ × Kc. The crop coefficient scales the reference evapotranspiration to the plant and its growth stage.
  • Gross irrigation need = (ETc − effective rain) ÷ irrigation efficiency. Rain that soaks into the soil is subtracted, and the loss in the system (evaporation, wind, runoff, leaks) is added back by dividing by the efficiency.
  • Water to apply = gross need × area. One millimetre of water on one square metre is one litre, and one inch of water on 1,000 square feet is about 623 gallons.
  • Weekly water = daily water × 7, which suits a weekly watering schedule.

Example

On a day with ET₀ of 0.25 in (6.35 mm), a crop coefficient of 1.1 gives ETc = 0.275 in per day. After 0.05 in of effective rain, the net need is 0.225 in, and at 75% efficiency the gross need is 0.30 in per day. For 2,000 ft² (186 m²) this is about 374 gallons per day, or 2,618 gallons per week.

Why it matters

Watering by the plant’s actual demand avoids both waste and stress. The result helps to size a water tank or a pump, to estimate the cost of watering, to set a controller for a lawn or an orchard, and to check whether a water allowance is enough for a garden.

Good to know

The calculation gives an average for the period and assumes the soil can supply the water between irrigations. Sandy soils need more frequent and smaller watering than clay soils. Salinity, a deficit irrigation strategy or water restrictions change what you should apply. Check the plants and the soil moisture as well.

The drip irrigation calculator sizes the emitters for a system and the sprinkler run time calculator gives the minutes needed to apply a depth of water.

Frequently asked questions

What is a crop coefficient?

The crop coefficient Kc links the water use of a specific plant to the reference evapotranspiration ET₀. It is low for a young crop with little leaf cover, rises to a peak when the plants are fully grown, and falls again at maturity. Published tables give Kc for most crops by growth stage.

Where do I find ET₀?

Many weather services, universities and irrigation agencies publish a daily ET₀ for local stations. If none is available, you can estimate it from temperature and latitude with the reference evapotranspiration calculator, or use typical values of 2 to 4 mm per day in spring and 5 to 8 mm in summer for a mild climate.

What irrigation efficiency should I use?

Drip irrigation applies water at the roots with about 90% efficiency. Sprinklers lose water to wind and evaporation and reach about 70 to 80%, and surface or flood irrigation often reaches 50 to 60%. Using a lower efficiency gives a larger volume that covers the losses.

Should I subtract all the rain?

Only the part that soaks into the soil and stays in the root zone, called effective rain. Light rain of a few millimetres wets the foliage and evaporates, while heavy rain can run off. As a rough guide, count about 70 to 80% of the rain from small and medium showers.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.