Skip to content
Omnikalc

Loudness normalization calculator: how much will a platform turn your track up or down?

Enter the integrated loudness and true peak of your track and choose a platform target to get the gain applied, the new peak, the change in amplitude and the headroom.

Updated on
Your inputs
LUFS

Value out of range

dBTP

Value out of range

dBTP

Value out of range

Results

Gain applied by normalization

-4.5 dB

True peak after normalization
-4.8 dBTP
Change in signal amplitude
-40.4 %
Headroom under the ceiling
3.8 dB
The peaks stay under the ceiling

Streaming services and broadcasters adjust each track to a common loudness, so a loud master is turned down and a quiet one may be turned up. The loudness normalization calculator takes the integrated loudness and the true peak of your track, a platform target and a peak ceiling and gives the gain applied, the true peak after normalization, the change in signal amplitude and the headroom under the ceiling.

How the calculation works

  • Gain = target loudness − the integrated loudness of your track, in decibels. A negative gain turns the track down and a positive one turns it up.
  • True peak after normalization = the current true peak + the gain. Gain changes every level by the same number of decibels.
  • Change in amplitude = (10^(gain ÷ 20) − 1) × 100. A gain of −6 dB halves the amplitude, and +6 dB doubles it.
  • Headroom = the ceiling − the new true peak. A negative value means that turning the track up would push the peaks over the ceiling.

Example

A master at −9.5 LUFS with a true peak of −0.3 dBTP, sent to a service that targets −14 LUFS: the gain is −14 − (−9.5) = −4.5 dB. The new true peak is −0.3 − 4.5 = −4.8 dBTP, which leaves 3.8 dB of headroom, and the amplitude falls by 40.4 percent. The track is turned down, so the loud master gains nothing there.

Why it matters

Mastering for a loudness target avoids surprises. A track pushed to the limit gets turned down on most services, and the extra compression only costs punch. Knowing the gain in advance lets you choose a master level that sounds the same everywhere, and keeps the peaks clean after lossy encoding.

Good to know

The targets vary by service and some change their rules over time, so check the current guidelines of each platform. Gain is applied to the whole track in one block, so its dynamics do not change. Integrated loudness must be measured on the final master with a meter that follows the ITU-R BS.1770 standard.

The speaker SPL calculator estimates sound levels in decibels and the audio file size calculator estimates the storage that a recording uses.

Frequently asked questions

What is LUFS?

It means loudness units relative to full scale. It measures the perceived loudness of an entire track, using a filter that models the sensitivity of the ear and a gate that ignores silence. One LU is one decibel, so a change of 1 dB in level is a change of 1 LU.

Will my track sound worse when it is turned down?

No. A track mastered louder than the target is simply turned down, with no loss of quality, but it gives no advantage, and the dynamic range lost in heavy limiting stays lost. Many engineers now aim for a master near the target and keep more dynamics.

What if my track is quieter than the target?

Some services only turn tracks down and leave quiet ones as they are. Others turn them up, usually with a limiter to avoid clipping. If the headroom shown is negative, the track would need such a limiter, which can change the sound.

What is the difference between true peak and sample peak?

The true peak estimates the highest level of the signal between the samples, after conversion to analog or to a lossy format. It can exceed the highest sample by 1 to 3 dB. That is why platforms ask for a ceiling below 0 dBTP, often −1 dBTP.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.