Skip to content
Omnikalc

Bladder volume calculator: from ultrasound length, width and height

Enter the three bladder dimensions from an ultrasound to get the bladder volume and, after voiding, the post-void residual volume, bladder capacity and the residual share.

Updated on

Educational tool, not medical advice: this page does not diagnose and does not replace a doctor, nurse or pharmacist. It has not been reviewed by a healthcare professional. Editorial and medical policy

Your inputs

Value out of range

Value out of range

Value out of range

mL

Value out of range

Results

Estimated bladder volume

36 mL

Normal residual (50 mL or less after voiding)

Residual as a share of capacity

11%

Bladder capacity (voided plus residual)
336 mL

This calculator is for general information and education. It is not medical advice and does not replace the advice of your doctor or a registered dietitian.

A bladder that does not empty fully can cause infections, leaks and kidney damage. This bladder volume calculator uses the three bladder dimensions from an ultrasound to estimate the volume in milliliters, and after the patient has passed urine it shows the post-void residual, the bladder capacity and the residual as a share of the capacity.

How the calculation works

  • Bladder volume = length × width × height × correction factor, with all three measurements in centimeters.
  • Correction factor = 0.52 for an ellipsoid, the standard value; some scanners use 0.7.
  • Capacity = volume passed just before the scan + the volume left in the bladder.
  • Residual share = volume left ÷ capacity.
  • Interpretation of a post-void residual: 50 mL or less is normal, up to 100 mL is acceptable in older adults, above 200 mL is significant retention.

Example

After passing 300 mL, an ultrasound shows a bladder of 5 cm by 4 cm by 3.5 cm. The residual volume is 0.52 × 5 × 4 × 3.5 = 36 mL, which is normal. The capacity is 336 mL and the residual is 11 % of it.

Why it matters

Measuring the urine left behind after voiding is a key test in men with urinary symptoms, in patients after surgery or with a catheter, and in people with nerve problems that weaken the bladder. The ellipsoid formula gives a quick, bedside estimate that helps decide whether a catheter, a medicine or further tests are needed.

Good to know

The formula assumes a regular shape and the estimate can be off by 20 to 30 percent, more when the bladder is nearly empty or oddly shaped. The measurements must be taken in two planes at right angles, at the widest points, and the scan should come within minutes of voiding. A single value is less useful than a repeat, because the residual varies from one void to the next. The result needs to be interpreted with symptoms and the clinical picture by a doctor, and a high value does not by itself call for treatment.

The water intake calculator estimates how much to drink, the BUN to creatinine calculator interprets kidney blood tests, and the eGFR calculator estimates kidney function.

Frequently asked questions

How is bladder volume calculated from an ultrasound?

Multiply the length, width and height in centimeters by 0.52, which treats the bladder as an ellipsoid. The result in cubic centimeters equals the volume in milliliters.

What is a normal post-void residual?

After a good void the bladder should contain less than 50 mL. Up to 100 mL can be acceptable in older adults, and a residual over 200 mL suggests significant retention.

Is a bladder scanner more accurate than the formula?

Handheld scanners use the same idea with automatic measurements and are usually within 10 to 20 percent of the true volume, but they are less reliable with obesity, ascites, a pelvic mass or a small volume.

What causes a high residual?

A blocked outlet, such as an enlarged prostate or a narrowed urethra, a weak bladder muscle from nerve damage or diabetes, constipation, and some medicines.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.