Skip to content
Omnikalc

BJT bias calculator: collector current, VCE and Q-point of a voltage divider bias

Enter the supply, the divider resistors, the collector and emitter resistors and the gain of an NPN transistor to get the collector current, the VCE, the Q-point and the stiffness of the bias.

Updated on
Your inputs
V

Value out of range

kΩ

Value out of range

kΩ

Value out of range

kΩ

Value out of range

kΩ

Value out of range

Value out of range

V

Value out of range

Results

Collector current IC

1.324 mA

Collector-emitter voltage VCE
7.76 V
VCE as a share of the supply
64.6%
Q-point near the middle: good swing
Power dissipated in the transistor
10.27 mW
Stiffness ratio (R1∥R2) / (β RE)
0.055
Stiff bias: IC depends little on β

The voltage divider bias sets the operating point of a bipolar transistor with two base resistors and an emitter resistor. The BJT bias calculator gives the collector current, the collector-emitter voltage, the position of the Q-point, the power and the stiffness of the bias.

How the calculation works

  • Enter the supply voltage and the two base resistors R1 and R2 of the voltage divider that sets the base voltage.
  • Enter the collector resistor RC and the emitter resistor RE, and the current gain β of the transistor (from the data sheet, with a typical value).
  • Enter the base-emitter voltage (0.65 to 0.7 V for a silicon transistor).
  • The calculator replaces the divider with its Thévenin equivalent, and gives the collector current, the collector-emitter voltage, the position of the Q-point and the stiffness of the bias.

Example

An NPN transistor with β = 150 is biased from 12 V with R1 = 47 kΩ, R2 = 10 kΩ, RC = 2.2 kΩ and RE = 1 kΩ. The Thévenin voltage is 12 × 10 / 57 = 2.105 V and the resistance is 8.246 kΩ. The base current is (2.105 − 0.7) / (8.246 + 151 × 1) = 0.00883 mA, so the collector current is 1.324 mA. The collector-emitter voltage is 12 − 1.324 × 2.2 − 1.332 × 1 = 7.76 V, or 64.6% of the supply, which is good. The transistor dissipates 10.27 mW, and the stiffness ratio is 0.055, below 0.1.

Why it matters

The calculator helps electronics students, makers and designers to bias a common-emitter amplifier or a switching stage, to check that the transistor is not near saturation, and to see how much the current changes with β. It replaces the manual solution of the Thévenin equations.

Good to know

Use the minimum and the maximum β of the data sheet to see the spread of the collector current, which is wide for a transistor from a batch. Choose the resistors from standard values and check the power of the transistor against its rating. Add a bypass capacitor across RE for a higher AC gain, and coupling capacitors at the input and output.

The voltage divider calculator gives the divider of the base, the transistor base resistor calculator sizes a switching stage, the Ohm’s law calculator covers the basic relations, and the op-amp gain calculator handles the linear amplifiers with ICs.

Frequently asked questions

What is the voltage divider bias?

It is the most common way to set the operating point of a bipolar transistor in an amplifier. Two resistors R1 and R2 give a base voltage, and the emitter resistor RE stabilizes the collector current by negative feedback. If the current rises, the voltage across RE rises, the base-emitter voltage falls and the current goes down. The result depends little on the gain β of the transistor.

How are the values computed?

The calculator replaces the divider with a Thévenin source, Vth = Vcc × R2 / (R1 + R2) in series with Rth = R1 ∥ R2. The base current is IB = (Vth − VBE) / (Rth + (β + 1) × RE), the collector current is IC = β × IB, and VCE = Vcc − IC × RC − IE × RE. The exact equations are used, with no approximation of a very large β.

Where should the Q-point be?

For a small-signal amplifier with the largest symmetric swing, VCE is about half of the supply, or somewhat less if the emitter is bypassed. The calculator flags a Q-point below 10% as near saturation and above 70% as near cutoff. A typical design places about 10% of the supply across RE, for the stability, and half of the rest across VCE.

How stiff should the bias be?

A common rule is Rth ≤ 0.1 × β × RE, so that the base current does not change the base voltage too much, and IC varies little with β. The calculator shows the ratio. A lower R1 ∥ R2 is stiffer but loads the input and uses more current from the supply, so it is a compromise. This tool gives the DC point only, not the gain or the bandwidth.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.