Skip to content
Omnikalc

Ligation calculator: how much insert for your vector?

Enter the vector amount and length, the insert length and the molar ratio to get the insert mass, the femtomoles of each and the volumes of vector and insert to pipette.

Updated on
Your inputs
ng

Value out of range

bp

Value out of range

bp

Value out of range

: 1

Value out of range

ng/µL

Value out of range

ng/µL

Value out of range

Results

Insert needed

50.0 ng

Vector stock to add

1.00 µL

Insert stock to add

2.00 µL

Vector in the reaction
25.3 fmol
Insert in the reaction
75.8 fmol

A ligation joins an insert into a vector with T4 DNA ligase, and its success depends on the molar ratio of insert to vector. The ratio is in molecules, so the amount in nanograms depends on the length of each piece. This ligation calculator takes the vector amount, the vector and insert lengths, the molar ratio and the stock concentrations to give the insert mass, the femtomoles of vector and insert, and the volumes to add.

How the calculation works

  • Insert mass = molar ratio × vector mass × (insert length ÷ vector length). Mass is proportional to length for the same number of molecules.
  • Picomoles of DNA: 1 ng of 1,000 bp DNA is about 1.52 fmol, since an average base pair weighs 660 Da. So fmol = ng × 1,000 ÷ (0.66 × length in bp).
  • Insert in fmol = molar ratio × vector fmol.
  • Volumes = mass ÷ stock concentration, for the vector and for the insert.

Example

A ligation uses 50 ng of a 3,000 bp vector with a 1,000 bp insert at a 3 : 1 molar ratio. The insert needed is 3 × 50 × 1,000 ÷ 3,000 = 50 ng. The vector is 25.3 fmol and the insert 75.8 fmol. With a vector stock of 50 ng/µL and an insert stock of 25 ng/µL, add 1.00 µL of vector and 2.00 µL of insert.

Why it matters

Molecular biologists do this calculation for every cloning experiment, and an error in the ratio is a frequent reason for a failed ligation. A calculator saves a spreadsheet and avoids confusion between mass and moles, particularly when an insert is much shorter than the vector.

Good to know

The calculation uses the average mass of 660 Da per base pair for double-stranded DNA. Measure the concentration of the DNA after purification, since a gel-purified fragment can be lost or contaminated, and check it by a gel or a fluorometer. The ratio is a starting point and the best value depends on the ends, the size of the insert and the competent cells. For multi-fragment assemblies, such as Gibson or Golden Gate, follow the kit’s recommendations for amounts, which are given by length and in fmol.

The DNA concentration calculator converts absorbance, the DNA copy number calculator converts mass to molecules and the molarity calculator finds the concentration of a solution.

Frequently asked questions

What molar ratio should I use for ligation?

A ratio of 3 insert molecules to 1 vector molecule is a common start for a sticky-end ligation. Use 1 : 1 to 2 : 1 for a large insert, and up to 5 : 1 to 10 : 1 for blunt ends or for a very short insert. If the colonies are few, try different ratios in parallel.

Why do I calculate the mass in place of the volume?

Ligase joins molecules, not nanograms. A short insert has far more molecules than a long vector of the same mass, so the mass of the insert is scaled with its length to reach the desired ratio.

How much vector should I use?

The usual range is 20 to 100 ng of vector in a 10 to 20 µL reaction. Too much DNA lowers the efficiency, and too little gives few transformants. Dephosphorylated vectors lower the background of the empty vector.

How is the number of picomoles calculated?

The weight of a double-stranded DNA molecule is 660 Da per base pair, on average. One picomole of a 3,000 bp vector weighs 1.98 µg, and the calculator converts mass to moles using this value.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.