Skip to content
Omnikalc

Shockley diode equation calculator: what current flows at a given voltage?

Enter the saturation current, the ideality factor, the temperature and the voltage to get the diode current, the thermal voltage, the dynamic resistance and the voltage needed for a target current.

Updated on
Your inputs

Value out of range

Value out of range

°C

Value out of range

V

Value out of range

mA

Value out of range

Results

Current at that voltage

13.871 mA

Thermal voltage
25.69 mV
Dynamic resistance at that point
1.85 Ω
Voltage needed for the target current
0.592 V
Power dissipated at that point
8.32 mW

The current in a diode grows exponentially with the voltage across it, and the Shockley equation describes this. The Shockley diode equation calculator takes the saturation current, the ideality factor, the junction temperature, the voltage and a target current and gives the diode current, the thermal voltage, the dynamic resistance, the voltage needed for the target current and the power dissipated.

How the calculation works

  • Thermal voltage Vt = k × T ÷ q, which is 25.7 mV at 25 °C (298.15 K). It rises by about 0.085 mV for each degree.
  • Shockley diode equation: I = Is × (e^(V ÷ (n × Vt)) − 1), where Is is the saturation current, n the ideality factor and V the voltage across the diode.
  • Dynamic resistance rd = n × Vt ÷ I. It is the slope of the voltage-current curve and falls as the current grows.
  • Voltage for a target current V = n × Vt × ln(I ÷ Is + 1). It gives the forward drop of the diode at that current.

Example

A silicon diode with Is = 1 pA and n = 1 at 25 °C has Vt = 25.69 mV. At 0.6 V the current is 1 pA × (e^(0.6 ÷ 0.02569) − 1) = 13.87 mA, and the dynamic resistance is 25.69 mV ÷ 13.87 mA = 1.85 Ω. The power dissipated is 0.6 V × 13.87 mA = 8.3 mW. To pass a target current of 10 mA the diode needs 0.592 V.

Why it matters

The equation underlies the design of rectifiers, clamps, temperature sensors, logarithmic amplifiers, solar cells and LEDs. Knowing how steeply the current rises with voltage explains why a diode cannot be driven from a plain voltage source without a resistor.

Good to know

The model is the ideal diode, valid for forward bias up to a moderate current. It does not include series resistance, high-level injection, breakdown or the capacitance of the junction. The saturation current varies with temperature and with the device, so it is best taken from a measured point of the real curve.

The LED resistor calculator sizes the series resistor that sets the current of an LED and the Zener diode calculator covers reverse breakdown regulation.

Frequently asked questions

What is the Shockley diode equation?

It is the ideal model of the current through a p-n junction: I = Is × (e^(V ÷ (n × Vt)) − 1). The current is almost zero below about 0.5 V for a silicon diode, then rises exponentially. Each increase of about 60 mV, for n = 1, multiplies the current by ten.

Why does the forward voltage fall as the diode warms?

The thermal voltage rises with the temperature, but the saturation current Is rises much faster, about doubling every 5 to 10 degrees. At a fixed current, the net effect is a drop of about 2 mV per degree. This makes diodes useful as temperature sensors, and it can cause thermal runaway in parallel diodes.

What is the ideality factor?

It describes how close a real junction is to the ideal one. A value of 1 corresponds to diffusion current, and 2 to recombination in the depletion region. Real diodes lie between, and LEDs are often between 1.5 and 3. You can measure n from the slope of the logarithm of the current against the voltage.

How accurate is the equation at high currents?

At high currents the series resistance of the semiconductor and the contacts adds a linear voltage drop, so the actual voltage is higher than the equation predicts. The equation also ignores breakdown in reverse. Use manufacturer curves for design near the limits.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.