Skip to content
Omnikalc

Bowl blank calculator: how big a blank do I need for my bowl?

Enter the finished size of the bowl, the shrinkage of the wood and the allowances to get the blank size, the rough turning diameter and the wall thickness.

Updated on
Your inputs

Value out of range

Value out of range

%

Value out of range

Value out of range

Value out of range

Results

Diameter of the blank

11.87 in

Diameter to rough turn
10.87 in
Height of the blank
5.00 in
Wall thickness when rough turning
1.09 in
Volume of the blank
3.84 board feet

A turned bowl made from green wood changes shape as it dries, so the blank has to start bigger than the finished bowl. This bowl blank calculator takes the finished diameter, the finished height, the shrinkage, the tenon allowance and the margin to give the diameter to rough turn, the diameter and height of the blank, the wall thickness for rough turning and the volume of wood.

How the calculation works

  • Diameter to rough turn = finished diameter ÷ (1 − shrinkage). Wood shrinks most across the growth rings as it dries, so a bowl turned from green wood becomes oval and smaller, and it must be rough turned larger than its final size.
  • Blank diameter = diameter to rough turn + 2 × margin. The margin gives room to true up the blank into a round on the lathe.
  • Blank height = finished height + tenon allowance + margin. The tenon or the chuck recess is cut in the base and is later turned away.
  • Wall thickness when rough turning = about 10% of the diameter to rough turn, which lets the wood dry evenly without cracking. Volume = π ÷ 4 × diameter² × height, in board feet.

Example

You want a bowl 10 in across and 4 in high from green wood that shrinks 8%. The diameter to rough turn is 10 ÷ 0.92 = 10.87 in. With a margin of 0.5 in on each side, the blank is 11.87 in across. The height is 4 + 0.5 + 0.5 = 5.0 in. The rough-turned wall should be about 1.09 in thick, and the blank holds π ÷ 4 × 11.87² × 5 ÷ 144 = 3.84 board feet of wood.

Why it matters

Wood turners use the numbers to choose a log or a board with enough wood, to cut blanks on the band saw and to estimate how much wood to buy or save from a fallen tree. Planning the size avoids ending up with a bowl that is too small after it dries.

Good to know

Shrinkage differs between species, between the heartwood and the sapwood and between the radial and the tangential directions, so the result is an estimate. The wall thickness rule suits green rough turning, and a bowl turned from dry wood needs no extra size. Check the blank for cracks and bark inclusions and follow the safety rules for the lathe and the band saw.

The board feet calculator converts the blank into lumber units, the wood moisture calculator tells you how much water the wood loses and the wood weight calculator estimates the weight.

Frequently asked questions

Why does a bowl need to be bigger than its final size?

When green wood dries, it shrinks mostly across the growth rings, which makes a round bowl turn into an oval and become smaller across. Turning the bowl a little bigger when green leaves room to dry and then re-turn to the final round shape. The calculator divides the final diameter by one minus the shrinkage.

What shrinkage should I use?

Shrinkage from green to dry across the grain varies with the species, from about 5% for some woods to over 10% for oak or beech when the tangential shrinkage is counted. The default of 8% suits a typical hardwood bowl. Look up the shrinkage for your species if you can, and use a moisture meter to know when the bowl is dry.

Why is the wall thickness about 10% of the diameter?

A common rule for rough turning green bowls is a wall of about one tenth of the diameter. Walls of this thickness dry at an even rate, and they leave wood to true the bowl after drying. Thinner walls dry fast but may crack, and thicker walls dry slowly and warp more.

What is the tenon allowance?

The tenon or recess is the part of the blank gripped by the chuck. It is cut on the base during the first turning and is removed at the end. Adding the allowance to the height ensures that the finished bowl has its full height once the base is turned.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.