Skip to content
Omnikalc

Buried tank flotation calculator: will an empty buried tank float?

Enter the size and weight of a buried tank, the soil cover and the soil weight to get the buoyant uplift with a high water table, the resisting force, the safety factor against flotation and the ballast needed.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

lb

Value out of range

ft

Value out of range

pcf

Value out of range

Value out of range

Results

Safety factor against flotation

0.73

The tank will float
Volume of water displaced by the tank
1,005 ft³
Uplift (buoyant) force with the water table at the surface
62,731 lb
Resisting force (tank weight and submerged soil above)
46,064 lb
Extra ballast needed (weight in air)
32,350 lb
Volume of concrete ballast needed
369 ft³

An empty tank buried in wet ground can be pushed up by the water. The buried tank flotation calculator compares the uplift with the weight of the tank and the soil above it, gives the safety factor against flotation and the ballast needed, for a septic, a storage or a fuel tank.

How the calculation works

  • Enter the diameter and the length of the buried cylindrical tank, the weight of the empty tank and the depth of soil cover above it.
  • Enter the saturated unit weight of the soil, about 120 to 130 pcf for most soils. The calculator takes the worst case, with the groundwater at the ground surface.
  • Enter the safety factor required, usually 1.2 to 1.5 against flotation.
  • The calculator compares the uplift of the water displaced with the resisting weight of the empty tank and of the submerged soil over it, then gives the ballast needed to reach the safety factor.

Example

A tank of 8 ft of diameter and 20 ft of length, weighing 6,000 lb empty, is buried with 4 ft of cover of soil with 125 pcf. It displaces 1,005.3 ft³ of water, so the uplift is 62.4 × 1,005.3 = 62,731 lb. The submerged soil above it weighs (125 − 62.4) × 4 × 8 × 20 = 40,064 lb, so the resisting force is 46,064 lb. The safety factor is 0.73: the tank would float. To reach 1.25, a ballast of 32,350 lb is needed, which is 369 ft³ of submerged concrete.

Why it matters

The calculator helps contractors, installers, homeowners and students to check a tank before it is installed in a high groundwater area, to see how much concrete or soil is needed, and to understand why the manufacturers require anchoring. It is a first check before the design of the anchor system.

Good to know

Use the highest groundwater level that you can expect, such as after a storm or a flood. Do not rely on the weight of the contents, since the tank can be empty for cleaning or repair. Check the straps and the concrete slab for the full uplift. Ask the manufacturer for the anchoring details of the model.

The buoyancy calculator covers the force on a floating or submerged body, the tank volume calculator gives the volume of a tank, the concrete volume calculator sizes the slab and the septic tank calculator gives the size of a septic system.

Frequently asked questions

Why can a buried tank float?

An empty tank is mostly air. If the groundwater rises around it, for example after heavy rain, the tank is pushed up by the weight of the water that it displaces, the buoyancy of Archimedes. A tank of 1,000 ft³ displaces about 62,400 lb of water, far more than its own weight and the soil above it. Floated tanks have broken pipes, cracked and risen out of the ground.

Why use the water table at the surface?

It is the worst case, and it is the usual assumption for a design that does not have a measure of the highest groundwater. If you know that the water table stays below the tank, the uplift is zero. If the water is only part way up the tank, the uplift is smaller. The soil above the water table weighs more, but the submerged part of the soil weighs less, so for the check, the submerged unit weight is used.

How can flotation be prevented?

Add weight: a concrete slab under the tank that is anchored to it with straps, concrete collars, or more soil cover. Another way is to keep the tank filled with water or with its contents, which adds weight. Anchors in a deep slab and a drainage system around the tank that keeps the water table low are also used. The tank manufacturer gives the required anchoring for each model.

What are the limits of this calculator?

It treats a horizontal cylinder and counts only the weight of the soil prism right above the tank, without the friction on the sides, which would help. It does not include the buoyancy of the shape of the ends, the strength of the tank under the soil load, the strength of the straps and the slab, or the case of the tank partly filled. A professional must design the anchoring of a real tank.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.