Skip to content
Omnikalc

Buried pipe deflection calculator: modified Iowa formula for flexible pipe

Enter the cover, the soil weight, the pipe stiffness, the soil modulus, the diameter, the lag factor and the bedding constant to get the soil load, the predicted deflection and the ratio to the 5 % limit.

Updated on
Your inputs
ft

Value out of range

pcf

Value out of range

psi

Value out of range

in

Value out of range

Results

Predicted vertical deflection

1.47 %

Soil prism pressure on the pipe
6.67 psi
Predicted deflection of the pipe
0.18 in
Ratio to the 5 % limit
0.29
Within the usual 5 % limit

The buried pipe deflection calculator gives the soil prism pressure, the predicted vertical deflection and the ratio to the 5 % limit of a buried flexible pipe, with the modified Iowa formula, from the depth of cover, the weight of the soil, the stiffness of the pipe and the soil modulus.

How the calculation works

  • Enter the depth of cover, the unit weight of the soil and the diameter of the buried flexible pipe.
  • Enter the pipe stiffness, choose the soil modulus that fits the compaction of the bedding and choose the lag factor and the bedding constant.
  • The calculator finds the soil prism pressure, the predicted deflection in percent and in inches, and the ratio to the 5 % limit.

Example

A PVC pipe of 12 in with a stiffness of 46 psi is buried under 8 ft of soil of 120 pcf, so the prism pressure is 120 × 8 / 144 = 6.67 psi. With a modulus E′ of 1,000 psi, a lag factor of 1.5 and K = 0.100, the deflection is 1.5 × 0.100 × 6.67 / (0.149 × 46 + 0.061 × 1,000) = 1.47 %, or 0.18 in for the 12 in pipe. This is 0.29 of the usual limit of 5 %.

Why it matters

The calculator helps pipeline and sewer designers, contractors, inspectors and students to check that a PVC, polyethylene or fiberglass pipe will keep its shape under the backfill, to choose the bedding and the compaction, and to compare the effect of the cover and of the stiffness of the pipe.

Good to know

Place the bedding and the backfill in thin layers, compact the haunches under the pipe by hand, and use a clean granular material in the pipe zone. Measure the deflection a few weeks after the backfilling, and with a mandrel for the final acceptance. Keep the trench wide enough for the compaction, and add the live load of the traffic when the pipe is under a road.

The pipe wall thickness calculator checks the pipe for the internal pressure, the pipeline coverage calculator checks the minimum cover, the soil unit weight calculator converts the weights of the soil and the thrust block size calculator restrains the fittings.

Frequently asked questions

What is the modified Iowa formula?

The modified Iowa formula, from the work of Spangler, gives the vertical deflection of a buried flexible pipe from the load of the soil, the stiffness of the pipe and the stiffness of the soil around it. The deflection in percent is the lag factor times the bedding constant times the load, divided by 0.149 times the pipe stiffness plus 0.061 times the soil modulus. It shows that the soil support is usually more important than the pipe stiffness.

What is the soil modulus E′?

The modulus E′ is the reaction of the soil on the sides of the pipe to the horizontal movement. It depends on the type of the soil and on the compaction of the bedding and of the haunches, and it is the most uncertain term of the formula. A well-compacted granular backfill can have a modulus 10 times higher than the same soil dumped without compaction, which reduces the deflection by a large factor.

What deflection limit is used?

A long-term deflection of 5 % of the diameter is the usual limit for the thermoplastic pipes such as PVC and polyethylene, and the manufacturers and the standards of AWWA, ASTM and AASHTO give the limits for each material. The pipe is tested after the installation with a mandrel. A large deflection reduces the flow capacity and can cause buckling or a failure of the joints.

What are the limits of the calculator?

The calculator uses the dead load of the soil prism only. It does not include the live load of the traffic, a high water table, the buckling of the pipe, the compaction of the backfill that must be checked on site, or the pipe that is rigid, such as concrete or ductile iron, which carries the load by its strength. For a deep burial or a heavy load, use the standard of the pipe and a full analysis.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.