Skip to content
Omnikalc

Cyclone cut size calculator: which dust particles a cyclone collects

Enter the dimensions and the gas velocity of a cyclone separator, with the particle and gas properties, to get the Lapple cut size, the collection efficiency at a given particle size and the size collected at 90%.

Updated on
Your inputs
ft

Value out of range

Value out of range

ft/s

Value out of range

lb/ft³

Value out of range

lb/ft³

Value out of range

cP

Value out of range

µm

Value out of range

Results

Cut size d50 (Lapple)

4.70 µm

Collection efficiency at the particle size of interest
81.9 %
Moderate collection: consider a smaller cyclone or a filter downstream
Particle size collected at 90% (3 × d50)
14.1 µm
Particle size collected at 50%
4.70 µm

A cyclone removes dust from a gas by centrifugal force. The cyclone cut size calculator applies Lapple’s model to give the cut size d50, the collection efficiency at a chosen particle size and the particle size that is collected at 90%.

How the calculation works

  • Enter the inlet width of the cyclone, the effective number of turns of the gas in the body (5 to 6 for a standard high-efficiency cyclone), and the inlet gas velocity (50 to 70 ft/s).
  • Enter the densities of the particles and of the gas, the viscosity of the gas, and the particle size that you want to check.
  • The calculator applies Lapple’s cut size d50 = √[9 µ W / (2π Ne Vi (ρp − ρg))], the size of the particles that are collected with 50% efficiency.
  • It gives the collection efficiency at your particle size with Lapple’s curve η = 1 / [1 + (d50 / d)²], and the size collected at 90%.

Example

A cyclone has an inlet width of 0.5 ft, 5 effective turns and an inlet velocity of 50 ft/s. The dust has a density of 150 lb/ft³ and the gas (air at 0.075 lb/ft³ and 0.0185 cP) is hot. The cut size is d50 = √[9 × 1.243×10⁻⁵ × 0.5 / (2π × 5 × 50 × 149.9)] = 4.70 µm. For 10 µm particles, the collection efficiency is 1 / (1 + (4.70 / 10)²) = 81.9%. Particles of 14.1 µm (3 × d50) are collected at 90%.

Why it matters

The calculator helps air pollution control engineers, plant managers, woodworking and grain facility designers, and students to see which particles a cyclone collects, to compare designs, and to decide whether a fine filter is needed downstream. It supports the pre-cleaning step before a baghouse.

Good to know

Use the gas viscosity at the working temperature, which rises with the temperature. Increase the inlet velocity to improve the collection, but keep it below the limit at which the particles are re-entrained (about 80 ft/s). Use the particle size distribution of the real dust. Compute the pressure drop to size the fan.

The Stokes’ law calculator gives the settling velocity of a particle, the terminal velocity calculator covers falling objects, the Reynolds number calculator checks the flow regime and the centrifuge RCF calculator covers centrifugal separation.

Frequently asked questions

What is the cut size of a cyclone?

A cyclone separates particles from a gas by the centrifugal force in a swirling flow. The cut size d50 is the particle diameter for which half of the particles are collected and half escape. Larger particles are collected with a higher efficiency, smaller ones with a lower efficiency. It is the main number to compare cyclones or to choose one for a given dust.

What is Lapple’s equation?

Lapple’s model, from 1951, assumes that the gas makes Ne turns in the cyclone and that a particle is collected if it reaches the wall during the residence time. It gives d50 = √[9 µ W / (2π Ne Vi (ρp − ρg))]. The cut size falls when the inlet is narrower, the velocity is higher, the dust is denser or the gas is less viscous. A narrower inlet means a smaller cyclone.

How is the efficiency computed?

Lapple’s curve gives the efficiency for a particle of diameter d as η = 1 / [1 + (d50 / d)²]. At d = d50 it is 50%, at d = 3 d50 it is 90% and at d = 10 d50 it is 99%. The overall efficiency of a real dust is found by summing the efficiencies over its size distribution. This simple curve is conservative for large particles.

What are the limits of this calculator?

The Lapple model is a first estimate with an accuracy of about ±30% on the cut size. It ignores the re-entrainment of the dust, the effect of the dust loading, which increases the efficiency, and the leakage at the hopper. Modern models such as Barth or Leith-Licht are more accurate. The pressure drop, which is about 4 to 8 inlet velocity heads, must also be computed to size the fan.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.