Skip to content
Omnikalc

Fire alarm standby battery capacity calculator

Enter the standby current and time, the alarm current and time and the margin to get the ampere-hours and the standard battery size of a fire alarm system.

Updated on
Your inputs
A

Value out of range

h

Value out of range

A

Value out of range

min

Value out of range

Value out of range

Results

Standard battery size to use

18 Ah

Standby capacity
10.80 Ah
Alarm capacity
0.27 Ah
Required capacity with the margin
13.28 Ah

The fire alarm battery calculator gives the standby and alarm ampere-hours, the required capacity with a margin and the standard battery size of a fire alarm system, from the currents and the times of the code.

How the calculation works

  • Enter the standby current of the panel and the devices and the standby time required.
  • Enter the alarm current with all the horns and strobes on and the alarm time.
  • Enter the margin factor. The calculator gives the ampere-hours and the standard battery size.

Example

A fire alarm panel draws 0.45 A in standby for 24 h, that is 10.80 Ah. In alarm it draws 3.2 A for 5 min, that is 3.2 × 5 / 60 = 0.27 Ah. With a margin of 1.2 the required capacity is (10.80 + 0.27) × 1.2 = 13.28 Ah, so you choose the next standard size, an 18 Ah battery.

Why it matters

The calculator helps fire alarm designers, installers, electrical contractors and facility managers to size the batteries of a panel or a power supply, to check an existing system when devices are added and to prepare the submittal.

Good to know

Add up the currents from the data sheets and use the alarm current with all the notification appliances on, since the worst case is the one that counts. Choose a battery whose rated capacity is at the 20 hour rate or at the rate stated by the panel maker, and do not count on the full capacity at a high discharge current. Test the batteries every year, replace them on schedule and label the date of installation on the case. Keep the battery calculation sheet in the project file, with the data sheets it comes from, so that the next change to the system can be checked against it.

The emergency egress lighting calculator spaces the exit luminaires, the smoke detectors calculator counts the detectors, the UPS runtime calculator gives the backup time of a battery and the battery life calculator gives the run time of a pack.

Frequently asked questions

How is the battery capacity found?

The capacity is the standby current times the standby time plus the alarm current times the alarm time, in ampere-hours, and the sum is multiplied by a margin. NFPA 72 asks for a battery that can run the system for 24 hours in standby and then 5 minutes in alarm, or 15 minutes for a voice evacuation system, with a stated end voltage. Some systems, such as those with a generator, can use a shorter standby time.

Why add a margin?

A battery loses capacity with age, with cold and with a high discharge rate, so a new battery of exactly the capacity needed will be too small after a few years. A factor of 1.2 is the common choice, and it keeps 20 % of margin. Many panel makers publish a battery calculation sheet and ask for this 20 %. A cold room or a long run may call for a higher factor, and the batteries must be replaced every 4 to 5 years.

Does the standby time depend on the code?

Yes. The 24 hours and 5 minutes are those of NFPA 72 for a typical local system. Other standards and local rules set other times, for example the EN 54-4 or a national rule of Europe, and authorities may ask for a longer standby or a generator. Enter the times of the rules that apply to your project, and check them with the authority having jurisdiction before you order the batteries.

What does the calculator leave out?

The calculator takes the currents you give it. It does not add up the devices one by one, the voltage drop of the circuits, the charger rating, the end of discharge voltage or the derating at low temperature. Sum the standby and alarm current of the panel, the detectors, the modules and the notification appliances from the data sheets, and check that the charger can recharge the battery within the time the code asks for.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.