Skip to content
Omnikalc

How do you size a storage loft in your garage?

Enter the loft length and depth, the joist spacing, the size of a plywood sheet and the design load: get the floor area, the joists, the joist lumber, the sheets and the load the platform is designed for.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

in

Value out of range

sq ft

Value out of range

lb/sq ft

Value out of range

Results

Loft floor area

80 sq ft

Load the loft is designed for

1,600 lb

Garage ceiling joists and trusses are often not designed for storage: have the framing, joist size and fixings checked by a builder or engineer, use joist hangers and ledgers bolted to studs, and add a guardrail on any open edge
Joists
8
Joist lumber
64 ft
Plywood sheets (10% waste)
3

The space above a garage door or between the ceiling joists is often the largest unused storage area in a house. A storage loft or overhead platform turns it into room for seasonal items, camping gear and holiday decorations. This calculator sizes the platform: joists, plywood and the load it is designed to carry.

How the calculation works

  • Loft floor area = length × depth
  • Joists = length ÷ joist spacing, rounded down, + 1
  • Joist lumber = joists × depth (the joist span)
  • Plywood sheets = area × 1.1 for waste ÷ sheet area, rounded up
  • Design load = area × load per sq ft

A 10 × 8 ft loft has 80 sq ft of floor. With joists 16 in apart it needs 8 joists spanning 8 ft, or 64 ft of joist lumber, and 3 sheets of 4 × 8 plywood with 10% waste. Designed for 20 lb per sq ft, a common figure for light attic storage, it is meant to carry about 1,600 lb in total, spread over the floor.

Typical design loads

Use Load per sq ft
Light storage, boxes of clothes and decorations 10 to 20 lb
Mixed storage, tools and camping gear 20 to 40 lb
Habitable loft or heavy storage 40 lb or more

Garage ceilings are usually built to hold drywall, not storage. Ceiling joists are often 2 × 4 or 2 × 6, and trusses must never be cut or loaded beyond their design without an engineer’s approval.

Building tips

  • Size the joists for the span and load from a span table, or have a builder or engineer check them; 2 × 8 or 2 × 10 joists are common for an 8 to 12 ft span.
  • Bolt a ledger board to the wall studs and hang the joists on joist hangers; on the open side, support the platform on a beam and posts or on the wall framing.
  • Use 3/4 in plywood or OSB, glued and screwed, so the floor does not bounce.
  • Leave enough headroom below for the garage door, its opener and your vehicle, and check the door track is clear.
  • Add a guardrail on any open edge and a solid ladder or pull-down stairs for access.
  • Store the heaviest items over the supports, not in the middle of a span, and label the design load on the loft.

Frequently asked questions

How many joists for a 10 ft garage loft?

Eight joists at 16 in on center for a 10 ft length, or 64 ft of lumber for an 8 ft span.

How much weight can a garage storage loft hold?

It depends on the joists and supports; light storage lofts are often designed for 20 lb per sq ft, or about 1,600 lb for 80 sq ft.

Can I store things on my garage ceiling trusses?

Not without checking: trusses are designed for specific loads and must never be cut; ask an engineer or the truss maker.

How much plywood for an 80 sq ft loft?

Three 4 × 8 sheets of 3/4 in plywood, including 10% for waste.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.