Skip to content
Omnikalc

Gravity retaining wall stability calculator: factors of safety against overturning and sliding

Enter the wall height and base width, the unit weights, the backfill friction angle and the base friction to get the Rankine thrust, the factors of safety against overturning and sliding, the eccentricity and the maximum base pressure.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

lb/ft³

Value out of range

°

Value out of range

lb/ft³

Value out of range

Value out of range

Results

Factor of safety against overturning

4.05

Overturning safety is adequate (2 or more)
Active thrust of the backfill (Rankine)
2,000 lb/ft
Factor of safety against sliding
2.25
Sliding safety is adequate (1.5 or more)
Eccentricity of the resultant over B/6
0.74
The resultant is in the middle third: no tension under the base
Maximum bearing pressure under the base
2,611 psf

The gravity retaining wall stability calculator checks a gravity wall against overturning and sliding and finds the eccentricity of the resultant and the maximum bearing pressure, from the wall dimensions and the Rankine active thrust of the backfill.

How the calculation works

  • Enter the height and the base width of the gravity wall and the unit weight of its material (concrete is about 150 lb/ft³).
  • Enter the friction angle and the unit weight of the level granular backfill behind the wall.
  • Enter the friction coefficient between the base and the soil, which is often tan of two thirds of the friction angle.
  • The calculator finds the Rankine active thrust, the overturning and sliding factors of safety, the eccentricity and the maximum bearing pressure.

Example

A rectangular concrete wall is 10 ft high and 6 ft wide, with a backfill of φ = 30° and 120 lb/ft³. Then Ka = 1/3 and the thrust is 0.5 × 0.333 × 120 × 10² = 2,000 lb/ft. The wall weighs 10 × 6 × 150 = 9,000 lb/ft. The overturning moment is 2,000 × 10 / 3 = 6,667 and the resisting moment 9,000 × 3 = 27,000 lb·ft/ft, so the overturning factor is 4.05. The sliding factor is 9,000 × 0.5 / 2,000 = 2.25. The eccentricity is 0.741 ft, 0.74 of B/6, and the maximum pressure is 2,611 psf.

Why it matters

The calculator helps engineers, contractors and students to make a preliminary design of a gravity wall of concrete, masonry or stone, to find the width of base needed for the safety factors and to see the effect of the backfill and of the friction of the base. It gives the checks that a hand calculation of the stability requires.

Good to know

Use a drained granular backfill and provide drainage behind the wall with weep holes or a drain. Use the friction coefficient of the geotechnical report, and a conservative value of 0.4 to 0.5 for a concrete base on sand. Compare the maximum pressure with the allowable bearing pressure. Do not count on the passive pressure in front of the base if the soil can be dug or eroded.

The Rankine earth pressure calculator gives the thrust in detail, the retaining wall calculator covers the materials, the gabion calculator covers gabion walls and the footing size calculator checks the bearing capacity.

Frequently asked questions

What does the calculator check?

It checks the three external stability modes of a gravity wall: overturning about the toe, sliding along the base and the bearing pressure under the base, with the location of the resultant. The wall must also be checked for the overall stability of the slope, the settlement and the internal strength of the wall. The usual minimum factors are 2.0 for overturning and 1.5 for sliding.

How is the earth pressure found?

The calculator uses the Rankine active pressure for a level granular backfill without water or surcharge, a thrust Pa = 0.5 Ka γ H² acting at one third of the height. The Coulomb theory with wall friction gives a smaller value for a rough wall. If there is a water table behind the wall, a surcharge, a sloping backfill or a cohesive soil, the thrust is much larger and drainage is essential.

What is the middle third rule?

The resultant of the weight and of the thrust should fall in the middle third of the base, which is within B/6 from the center. In this case the whole base stays in compression, and the pressure goes from a maximum at the toe to a minimum at the heel. Outside the middle third the pressure is only under part of the base, and the maximum pressure is higher. For soil foundations the eccentricity should not exceed B/6.

What are the limits of the calculation?

The wall is taken as a simple rectangle, and the passive resistance of the soil in front of the base is ignored, which is conservative. A tapered wall, a key under the base or a heel with soil on top have a better behavior, and the weight of the soil on the heel counts. The bearing pressure must be compared with the allowable bearing capacity of the soil, and a geotechnical report is needed.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.