Skip to content
Omnikalc

Rankine earth pressure calculator: how hard does soil push on a wall?

Enter the friction angle, the unit weight, the wall height and the surcharge to get the active thrust, the Ka, Kp and K0 coefficients and the resultant height.

Updated on
Your inputs
°

Value out of range

pcf

Value out of range

ft

Value out of range

psf

Value out of range

Results

Active thrust on the wall

1,425.7 lbf/ft

Active earth pressure coefficient Ka
0.307
Passive earth pressure coefficient Kp
3.255
At-rest earth pressure coefficient K0
0.470
Height of the resultant above the base
2.90 ft

Any wall that holds back soil must resist the push of the earth. The Rankine earth pressure calculator takes the friction angle, the unit weight of the backfill, the wall height and a surcharge, and gives the active thrust per unit length of wall, the coefficients Ka, Kp and K0 and the height of the resultant above the base.

How the calculation works

  • Enter the friction angle of the backfill, its unit weight, the height of the wall and any surcharge on the ground behind it.
  • The active coefficient is Ka = tan²(45° − φ/2), the passive coefficient is Kp = tan²(45° + φ/2) and the at-rest coefficient is K0 = 1 − sin φ.
  • The active thrust per unit length of wall is Pa = ½ × Ka × γ × H² + Ka × q × H, the soil part plus the surcharge part.
  • The height of the resultant above the base is found by taking moments of the two parts: the soil triangle acts at H/3 and the uniform surcharge at H/2.

Example

A wall is 8 ft high with a granular backfill of φ = 32° and γ = 120 pcf, and a surcharge of 100 psf. Ka = tan²(29°) = 0.307, Kp = 3.255 and K0 = 0.470. The soil part of the thrust is 0.5 × 0.307 × 120 × 8² = 1,180 lbf/ft and the surcharge part is 0.307 × 100 × 8 = 246 lbf/ft, so Pa = 1,426 lbf/ft. The resultant acts 2.90 ft above the base, a bit below the mid-height because the surcharge adds weight to the upper part.

Why it matters

The thrust grows with the square of the height, so doubling the wall quadruples the load on it. A quick estimate shows how much a surcharge or a change of backfill matters, why drainage is essential and how large the forces are before sizing the wall, the footing or the anchors.

Good to know

Rankine’s theory is a classic simplification. Real walls move and rotate, the wall surface is rough, the backfill may be sloped, layered, wet or cohesive, and compaction adds pressure. Seismic loads also matter in some regions. Use this as a learning tool and a first check, and have a licensed engineer design any wall of structural importance.

The retaining wall calculator covers materials and cost of walls, the footing size calculator sizes the base, the factor of safety calculator sets margins against sliding and overturning, and the angle of repose calculator covers loose material.

Frequently asked questions

What is Rankine's theory?

William Rankine's theory of 1857 gives the lateral earth pressure on a smooth, vertical wall that retains level ground. It assumes the soil is at the point of failure in a wedge behind the wall. The pressure grows in a straight line with depth, so the total thrust is the area of a triangle, and it acts one third of the way up.

What are Ka, Kp and K0?

Ka is the ratio of horizontal to vertical stress when the wall moves away from the soil and the soil is about to fail in an active state. Kp is the ratio when the wall is pushed into the soil, in a passive state. K0 is the ratio at rest with no movement. Ka is the smallest, K0 is in between and Kp is the largest.

How does a surcharge change the thrust?

A uniform load on the ground, such as a road or a stockpile, adds a constant pressure Ka × q over the whole height of the wall. This adds a rectangle to the pressure triangle, increases the thrust and raises the point where the resultant acts. A heavy surcharge can matter more than the soil itself for a low wall.

What does the calculator leave out?

It assumes a dry cohesionless backfill, a smooth vertical wall and level ground. Water behind a wall can double the load, cohesion reduces the pressure near the top, friction between the wall and the soil changes the result, and sloping backfill needs another formula. Real retaining walls must be designed by an engineer, with drainage.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.