Skip to content
Omnikalc

Minimum curve radius calculator: design speed, superelevation and friction

Enter the design speed, the maximum superelevation and the side friction factor of a road to get the minimum radius of a horizontal curve and the maximum speed on the radius available.

Updated on
Your inputs
mph

Value out of range

%

Value out of range

Value out of range

ft

Value out of range

Results

Minimum radius

1,200 ft

Superelevation plus friction (e + f)
20.0 %
Maximum speed on the available radius
67.1 mph
Available radius against the minimum speed
1.12
The radius meets the design speed with a margin

The minimum curve radius is the tightest circular curve that a road can have for a given design speed, with the superelevation and the side friction that are allowed. The minimum radius calculator gives the radius, the sum e + f, and the maximum speed on a radius that you have available.

How the calculation works

  • Enter the design speed of the road and the maximum superelevation allowed (the banking of the road, often 6 to 12%).
  • Enter the side friction factor, the part of the tire grip used to hold the vehicle in the curve. Standards give values that fall as the speed rises (for example 0.12 at 60 mph).
  • Enter the radius available on the site, to check it against the design speed.
  • The calculator gives the minimum radius R = V² / (15 (e/100 + f)), the maximum speed on your radius and the ratio between the two.

Example

A highway has a design speed of 60 mph, a maximum superelevation of 8% and a side friction factor of 0.12. The sum e + f is 0.08 + 0.12 = 0.20, so the minimum radius is 60² / (15 × 0.20) = 1,200 ft. On a site with 1,500 ft of radius available, the maximum speed is √(15 × 1,500 × 0.20) = 67.1 mph, which is 1.12 times the design speed, a comfortable margin.

Why it matters

The calculator helps civil engineers, students, planners and developers to size the curves of a road, a ramp, a driveway or a race track, and to check quickly if a site layout meets the design speed. It gives the first estimate before looking up the tables of the standard.

Good to know

Use the values of e and f from the standard for the design speed that you want, and not the maximum friction of the tire. Check the case of the lowest friction in wet weather, and the case of a slow vehicle on a high superelevation in snow and ice. Provide a transition curve for the changes of the cross-slope.

The banked curve calculator gives the physics of the turn, the stopping distance calculator sets the sight distance, the vertical curve calculator covers the profile of the road, and the speed distance time calculator converts the speeds.

Frequently asked questions

What is the formula for the minimum radius?

The point-mass model of a vehicle in a curve gives V² / (g R) = e + f, where e is the superelevation as a ratio and f the side friction factor. In US units, with V in mph, R in feet, this is R = V² / (15 (e + f)), and in metric units, with V in km/h and R in meters, it is R = V² / (127 (e + f)). A higher speed needs a larger radius, more banking or more friction.

How are e and f chosen?

The maximum superelevation is set by the standard according to the climate and the type of road: often 6 to 8% in snowy regions, up to 10 to 12% elsewhere, and lower in urban areas. The side friction factor is a design value much lower than the real friction of the tire, to keep the comfort and a safety margin. It falls from about 0.17 at 30 mph to 0.09 at 80 mph in the AASHTO tables.

What if the available radius is too small?

If the speed that the radius allows is lower than the design speed, you can increase the radius, reduce the design speed, add warning signs and a speed limit, or accept a lower standard with a design exception. The ratio in the calculator shows the margin, and a ratio under 1 means the curve does not meet the speed.

Does this replace the design standard?

No. The calculator uses the basic equation. A real design uses the tables of the standard for e and f at each speed, a transition curve between the tangent and the circular curve, the rate of change of the superelevation, the drainage and the sight distance. Check the local manual, such as the AASHTO Green Book, the highway standards of your country or the SETRA guide.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.