Skip to content
Omnikalc

Vertical curve calculator: K value, middle ordinate and high point

Enter the two grades, the curve length and the intersection elevation to get the K value, the middle ordinate, the high or low point and a sight distance check.

Updated on
Your inputs
%

Value out of range

%

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

K value (curve length per percent of grade change)

160.0 ft/%

The curve is long enough for the stopping sight distance
Minimum K for the stopping sight distance
83.7 ft/%
Algebraic difference in grades
5.00 %
Middle ordinate (offset from the grade intersection to the curve)
5.00 ft
Distance from the start of the curve to the high or low point
480.0 ft
Elevation of the high or low point
495.20 ft
Elevation at the start of the curve
488.00 ft

Where a road changes from one grade to another, the surveyor does not put in a sharp angle: the two grades are joined by a parabolic vertical curve. This calculator takes the incoming and outgoing grades, the length of the curve and the elevation of the grade intersection, and returns the K value, the middle ordinate, the high or low point and a check against the stopping sight distance.

How the calculation works

With grades g₁ and g₂ in percent and a curve length L:

  • Algebraic difference A = |g₂ − g₁|
  • K = L ÷ A
  • Middle ordinate e = A × L ÷ 800
  • Start of curve (PVC) elevation = intersection elevation − g₁ ÷ 100 × L ÷ 2
  • High or low point: x = g₁ × L ÷ (g₁ − g₂) from the start, with elevation y = y₀ + g₁x ÷ 100 + (g₂ − g₁)x² ÷ (200L)
  • Minimum K (crest) = S² ÷ 2,158; (sag) = S² ÷ (400 + 3.5 S), with S the stopping sight distance in feet

Example

Grades of +3 % and −2 % meet at elevation 500 ft with a curve 800 ft long. A = 5, so K = 160 ft/% and the middle ordinate is 5.00 ft. The curve starts at 488.00 ft. The crest is 480 ft from the start, at elevation 495.20 ft. For a stopping sight distance of 425 ft the minimum K is 83.7, so the curve is long enough.

Why it matters

A crest that is too sharp hides what lies beyond it, and a sag that is too sharp throws headlight beams into the ground. K connects the geometry to safety: the same K works at any grade difference, so a designer can check a curve in a few seconds. The high or low point locates the drainage inlets, since a sag with no outlet collects water.

Good to know

The curve length is measured horizontally and the formulas assume a symmetrical parabola. For very short curves the sight distance may exceed the curve length and a different formula applies. Standards (such as AASHTO) set the minimum K by design speed, and local rules may add comfort or drainage criteria. This tool is for education and is not a substitute for an engineered design.

In practice

Start from the sight distance the road needs, find the minimum K and multiply by A to get the shortest curve. Then round the length up to a whole multiple of 50 or 100 feet, keep the high point away from intersections and check the offset at each station before setting out.

The ski slope steepness calculator converts a grade to degrees, the stopping distance calculator gives the braking distance, and the banked curve calculator covers the horizontal case.

Frequently asked questions

What is a vertical curve?

It is the parabolic curve that joins two road grades. A crest curve connects an uphill grade to a downhill grade, and a sag curve connects a downhill grade to an uphill one. It smooths the change so vehicles ride comfortably and drivers can see far enough ahead.

What is the K value?

K is the horizontal length of curve needed for each 1 percent change in grade: K = L ÷ A. A larger K means a flatter curve and more sight distance. Design standards give a minimum K for each design speed.

Where is the high point of a crest curve?

It lies where the slope of the curve is zero, at a distance x = g₁ × L ÷ (g₁ − g₂) from the start of the curve, when the grades are in percent. The drainage low point on a sag curve is found the same way.

What does the middle ordinate tell me?

It is the vertical distance from the grade intersection to the curve at its midpoint, e = A × L ÷ 800 with A in percent. It shows how far the road surface sits below the intersection on a crest, or above it in a sag.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.