Skip to content
Omnikalc

True position calculator: is the feature within its GD&T position tolerance?

Enter the X and Y deviations, the position tolerance and the feature size to get the true position, the bonus tolerance at MMC and the share of tolerance used.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

mm

Value out of range

mm

Value out of range

mm

Value out of range

Results

Share of the allowed position tolerance used

75.9 %

Within the position tolerance
True position (diameter)
0.2884 mm
Bonus tolerance
0.0800 mm
Allowed position tolerance
0.3800 mm
Margin left in the tolerance zone
0.0916 mm

On a technical drawing, holes and pins are located within a tolerance zone, and checking a part means converting X and Y measurements into a single number. The true position calculator takes the X and Y deviations, the position tolerance, the feature type, the material condition and the actual size, and gives the true position, the bonus tolerance, the allowed tolerance, the share used and the margin left.

How the calculation works

  • Enter the measured deviations in X and Y of the feature from its nominal position, in millimetres.
  • Enter the position tolerance from the drawing, which is the diameter of the tolerance zone.
  • Choose the feature type and the material condition modifier. With MMC, you get a bonus tolerance equal to how far the actual size departs from the maximum material size.
  • The true position is a diameter: 2 × √(X² + Y²). The part passes if it is no larger than the allowed tolerance, which is the stated tolerance plus the bonus.

Example

A hole is 0.12 mm off in X and 0.08 mm off in Y. Its true position is 2 × √(0.12² + 0.08²) = 0.2884 mm. The drawing allows 0.30 mm at MMC, the MMC size is 10.00 mm and the measured hole is 10.08 mm, so the bonus is 0.08 mm and the allowed tolerance is 0.38 mm. The part uses 75.9 % of the tolerance and passes. Without the bonus (RFS), it would use 96.1 % of 0.30 mm, which still passes but with little margin.

Why it matters

Using the bonus tolerance at MMC turns some rejected parts into accepted ones without hurting the fit, because a larger hole accepts a pin with more offset. Computing it correctly saves scrap and avoids accepting parts that do not meet the drawing.

Good to know

The calculator follows the usual ASME Y14.5 convention for a cylindrical zone and a single feature, at one datum reference. It does not cover composite tolerances, projected zones, datum shift, patterns of features or the ISO variants. The drawing and the applicable standard always take precedence.

The bolt circle calculator gives hole coordinates, the taper angle calculator covers conical features, and the bend allowance and cutting speed calculators help with sheet metal and machining.

Frequently asked questions

What is true position in GD&T?

True position is a geometric tolerance that controls how far the axis or centre of a feature may deviate from its theoretical exact location. The tolerance is a cylinder (a circle in a plane) centred on the nominal position, so the deviation is a diameter, twice the radial distance.

Why is the true position twice the radial deviation?

The tolerance zone is defined by its diameter, but the measured deviation in X and Y gives a radius from the nominal centre. Doubling the radial distance 2 × √(X² + Y²) puts the result on the same basis as the diameter on the drawing.

What is bonus tolerance?

When a position tolerance is applied at maximum material condition (MMC), the tolerance zone may grow as the feature departs from its MMC size, since the mating part has more clearance. For a hole, the bonus is the actual size minus the MMC size. For a pin, it is the MMC size minus the actual size.

When does the bonus not apply?

The bonus applies only to features of size and when the tolerance is called out at MMC or LMC. With RFS (regardless of feature size), which is the default in the ASME Y14.5 standard, the tolerance does not change with size. Datum features can also have their own shift, which this calculator does not include.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.