Skip to content
Omnikalc

Bend allowance calculator: flat length of a sheet-metal bend

Enter the thickness, inside radius, K-factor, bend angle and flange lengths to get the bend allowance, bend deduction and the flat length to cut.

Updated on
Your inputs
in

Value out of range

in

Value out of range

Value out of range

°

Value out of range

in

Value out of range

in

Value out of range

Results

Flat blank length to cut

4.8575 in

Bend allowance (arc length along the neutral axis)
0.2275 in
Outside setback
0.1850 in
Bend deduction (flat length saved per bend)
0.1425 in
Sum of the two outside lengths
5.00 in

Before you cut a sheet-metal part, you need the flat length of the blank. A bend stretches the outer surface and compresses the inner one, so the flat length is not simply the sum of the flange lengths. This calculator uses the K-factor to find the bend allowance, the outside setback and the bend deduction, and then the length to cut for a single bend.

How the calculation works

  • Bend allowance = bend angle (in radians) × (inside radius + K-factor × thickness)
  • Outside setback = tan(angle ÷ 2) × (inside radius + thickness)
  • Bend deduction = 2 × outside setback − bend allowance
  • Flat length = outside length A + outside length B − bend deduction

The outside lengths are measured from the end of each flange to the virtual sharp, the point where the two outside faces would meet if the corner were not rounded.

Example

A 0.060 in sheet is bent through 90° with an inside radius of 0.125 in and a K-factor of 0.33. The bend allowance is 1.5708 × (0.125 + 0.33 × 0.060) = 0.2275 in. The outside setback is 0.125 + 0.060 = 0.185 in, so the bend deduction is 2 × 0.185 − 0.2274 = 0.1425 in. With outside flanges of 2 in and 3 in, the flat blank is 5 − 0.1425 = 4.857 in.

Why it matters

A part cut from the sum of its outside dimensions comes out too long by the bend deduction at each bend. On a bracket with six bends, that is almost an inch of error. Getting the flat length right avoids scrap, shims and holes that no longer line up, and it lets a laser or a shear cut blanks from a drawing without trial and error.

Good to know

The K-factor changes with the material, its hardness, the die opening, the forming method and the ratio of radius to thickness, so the value of 0.33 is a starting point and not a constant. Air bending, bottoming and coining give different results. The grain direction of the sheet also matters for tight bends. For a part with several bends, add the bend allowances of all of them to the lengths of the flat portions between them. This tool is for education: confirm with a test bend on your own press brake.

The metal weight calculator weighs the blank, the cutting speed calculator sets the speed for machining the flat, and the milling feed rate calculator gives the feed for a cutter.

Frequently asked questions

What is bend allowance?

It is the length of the arc that the neutral axis of the sheet follows around a bend. The neutral axis is the line inside the thickness that neither stretches nor shrinks. Adding the bend allowance to the two straight flanges, measured from the inside, gives the flat length of the blank.

What is the K-factor?

The K-factor is the position of the neutral axis as a fraction of the thickness, measured from the inside face. It is about 0.33 for tight bends in soft metal and moves toward 0.5 for large radii. The exact value depends on the material, the tooling and the method, so measure a test bend when precision matters.

What is the difference between bend allowance and bend deduction?

Bend allowance is added to the inside flange lengths. Bend deduction is subtracted from the sum of the outside lengths, which is how most drawings are dimensioned. Bend deduction equals twice the outside setback minus the bend allowance.

Does this work for angles other than 90 degrees?

Yes. The angle here is the deflection angle, the amount the flange turns: 90 for an L bend, 45 for a shallow one. The formulas use the tangent of half that angle for the setback and the full angle for the arc.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.