Skip to content
Omnikalc

Tuned mass damper calculator: Den Hartog optimal tuning for a structure

Enter the modal mass and the frequency of a structure and the mass ratio of the damper to get the damper mass, its optimal frequency and damping ratio, the spring stiffness, the damping coefficient and the equivalent damping.

Updated on
Your inputs
lb

Value out of range

Hz

Value out of range

%

Value out of range

Results

Optimal damper frequency

0.9804 Hz

Damper mass
10,000.00 lb
Optimal damper damping ratio
8.41 %
Damper spring stiffness
982.0 lb/in
Damper damping coefficient
26.804 lb·s/in
Peak dynamic amplification (undamped structure)
10.05
Equivalent damping ratio of the structure
4.98 %

A tuned mass damper is a small mass on a spring that absorbs the vibration of a tall building, a bridge or a floor. The tuned mass damper calculator applies the Den Hartog equations to give the damper mass, its optimal frequency, its damping ratio, the spring stiffness, the damping coefficient and the equivalent damping of the structure.

How the calculation works

  • Enter the modal mass of the structure for the mode to damp (the generalized mass of the first mode, often 25% to 50% of the total mass of a tall building) and its natural frequency.
  • Enter the mass ratio μ of the damper to the structure. Typical values are 0.5% to 5%, and a higher ratio gives a better and more robust damping.
  • The calculator applies the optimal parameters of Den Hartog for an undamped structure under a harmonic force: fopt = fs / (1 + μ) and ζopt = √(3μ / (8(1 + μ)³)).
  • It then gives the spring stiffness k = m ω² and the damping coefficient c = 2 ζ m ω of the damper, the peak amplification √(1 + 2/μ) and the equivalent damping ratio of the structure.

Example

A structure with a modal mass of 500,000 lb and a frequency of 1.00 Hz gets a damper with a mass ratio of 2%. The damper mass is 10,000 lb. The optimal frequency is 1.00 / 1.02 = 0.9804 Hz, and the optimal damping ratio is √(3 × 0.02 / (8 × 1.02³)) = 8.41%. With the mass 10,000 / 386.4 = 25.88 lb·s²/in and ω = 6.160 rad/s, the spring stiffness is 982 lb/in and the damping coefficient is 26.8 lb·s/in. The peak amplification falls to √(1 + 2/0.02) = 10.05, which is an equivalent damping of 4.98%.

Why it matters

The calculator helps structural and mechanical engineering students and designers to understand how a damper is tuned, to estimate its size for a given mass ratio and to see how much the vibration can fall. It gives the starting values for a detailed design.

Good to know

Use the modal mass of the mode to control, not the total mass. Check the stroke of the damper: it can be several times larger than the motion of the structure. Plan for the adjustment of the spring, since the frequency of the structure is uncertain and can change with time. Include the real structural damping in the final analysis.

The pendulum calculator gives the frequency of a pendulum damper, the wind load calculator estimates the excitation of a tall structure, the compression spring calculator sizes the spring and the earthquake magnitude calculator covers seismic events.

Frequently asked questions

What is a tuned mass damper?

A tuned mass damper (TMD) is a secondary mass attached to a structure through a spring and a dashpot. It is tuned to a frequency close to the one of the mode to control. When the structure starts to vibrate, the damper moves out of phase and absorbs energy, which reduces the motion. TMDs are used in tall buildings, footbridges, towers and chimneys to reduce the vibrations caused by wind or by people.

What are the Den Hartog optimal parameters?

For an undamped main structure and a harmonic force, the amplitude is the lowest when the frequency ratio of the damper is 1 / (1 + μ) and its damping ratio is √(3μ / (8(1 + μ)³)). The peak amplification of the structure is then √(1 + 2/μ). These formulas are the classical starting point, and they are used for the preliminary design of most dampers.

How large should the mass ratio be?

A larger mass ratio gives more damping and a wider range of frequencies where the damper works, but costs more and takes more space and weight. Most buildings use 0.5% to 2% of the modal mass, and a footbridge or a floor can use 2% to 5%. A small mass ratio makes the damper sensitive to a mistuning of the structure frequency, for instance when the stiffness or the mass changes with time.

What are the limits of this calculator?

It assumes a single mode, an undamped structure and a harmonic load. For random wind loading or an earthquake, the optimal values are slightly different, and the structural damping, the multiple modes, the stroke of the damper and the nonlinear effects must be included. A real project needs a dynamic analysis and testing by a specialist.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.