Skip to content
Omnikalc

How stiff is your coil spring?

Enter the wire diameter, coil diameter, number of active coils and material: get the spring rate, the force at a deflection, the Wahl-corrected stress and the stored energy.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

Value out of range

Results

Spring rate

2.478 N/mm

Force at this deflection

24.78 N

Spring rate in pounds per inch
14.15 lbf/in
Spring index (coil ÷ wire diameter)
10.00
Spring index between 4 and 12: a good range
Wahl correction factor
1.145
Corrected shear stress in the wire
180.6 MPa
Energy stored
0.1239 J

A coil spring pushes back with a force that grows in proportion to its compression: F = k × x. The spring rate k depends on the wire diameter, the coil diameter, the number of active coils and the material. This calculator gives the rate of a helical compression spring, the force at a chosen deflection, the energy stored, and the stress in the wire so that you can check it against the material’s limits.

How the calculation works

  • Spring rate k = G × d⁴ ÷ (8 × D³ × N)
  • Force F = k × deflection
  • Spring index C = D ÷ d
  • Wahl factor Kw = (4C − 1) ÷ (4C − 4) + 0.615 ÷ C
  • Shear stress τ = Kw × 8 × F × D ÷ (π × d³), and energy = ½ × k × x²

Example

A steel spring has a wire of 2 mm, a mean coil diameter of 20 mm and 8 active coils, with a shear modulus of 79.3 GPa. The rate is 2.478 N/mm (14.15 lbf/in). Compressed by 10 mm, it pushes with 24.78 N and stores 0.124 J. The spring index is 10, the Wahl factor is 1.145, and the shear stress in the wire is 180.6 MPa.

Where it is used

Suspensions, valves, pens, mattresses, switches and latches all use compression springs. Use the calculator to choose a wire and a coil count that give the force you need, to check that a spring does not exceed its stress limit at full compression, and to estimate the energy it stores. A hardened steel spring wire can often tolerate a stress of 40 to 50 percent of its tensile strength in static use.

Good to know

Compare the shear stress with the allowable value for the wire, at the largest deflection the spring will see, which is often when the coils touch (solid height). Springs in repeated use need a much lower stress to avoid fatigue. Halving the number of coils doubles the rate, and increasing the wire diameter by 20 percent doubles it. The formulas assume a straight spring that does not buckle, so long, thin springs need a guide or a rod.

For the vibration of a mass on a spring, use the spring-mass calculator, and for a simple linear spring, Hooke’s law. The shaft torsion calculator uses the same shear modulus.

Frequently asked questions

How do you calculate the stiffness of a coil spring?

The spring rate is k = G × d⁴ ÷ (8 × D³ × N), where G is the shear modulus, d the wire diameter, D the mean coil diameter and N the number of active coils.

What is the spring index?

The ratio of the mean coil diameter to the wire diameter. Values from 4 to 12 are easy to make and stress the wire evenly. Below 4 the spring is hard to coil, and above 12 it tends to tangle.

What is the Wahl factor?

A correction that accounts for the extra stress on the inside of the coil, caused by the curvature of the wire and by direct shear. It is larger for low spring indexes.

How do I get the stiffness of springs in series or parallel?

In parallel the rates add up. In series, the inverse of the total rate is the sum of the inverses of each rate.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.