Skip to content
Omnikalc

F-value calculator: is your heat process lethal enough?

Enter the process temperature, the hold time, the reference temperature, the z-value and the D-value to get the F-value and the log reductions.

Updated on
Your inputs
°F

Value out of range

min

Value out of range

°F

Value out of range

°F

Value out of range

min

Value out of range

Value out of range

Results

Equivalent time at the reference temperature (F-value)

4.22 min

The process reaches the target number of log reductions
Lethal rate (reference minutes per minute)
0.5275
Log reductions achieved
20.1
Hold time needed for the target
4.78 min
F-value needed for the target
2.52 min

A heat treatment kills organisms faster as the temperature rises, and the F-value puts every temperature and time on one scale. The thermal process F-value calculator takes the process temperature, the hold time, the reference temperature, the z-value, the D-value and the target log reductions, and gives the F-value, the lethal rate, the log reductions achieved, the hold time needed and the F-value needed.

How the calculation works

  • Enter the process temperature at the coldest point of the product and the hold time at that temperature.
  • Enter the reference temperature and the z-value of the target organism. For low-acid canning against botulinum spores, the classic values are 250 °F and 18 °F, which are 121.1 °C and 10 °C.
  • Enter the D-value, the time at the reference temperature that destroys 90 percent of the organism, and the target number of log reductions. The classic canning target is 12.
  • The lethal rate is 10^((T − Tref) ÷ z), the F-value is the lethal rate times the hold time, and the log reductions are the F-value divided by the D-value.

Example

A product is held at 245 °F for 8 minutes. The lethal rate is 10^((245 − 250) ÷ 18) = 0.5275, so each minute counts as 0.5275 minutes at 250 °F. The F-value is 0.5275 × 8 = 4.22 minutes. With a D-value of 0.21 minutes, the process gives 4.22 ÷ 0.21 = 20.1 log reductions, above the target of 12. The minimum hold time for 12 logs at 245 °F is 12 × 0.21 ÷ 0.5275 = 4.78 minutes.

Why it matters

The same lethality can be reached with a longer time at a lower temperature or a shorter time at a higher one. The F-value lets you compare them and check a process against a target, which is how food plants design retort and pasteurization cycles. It also shows how steeply the effect changes: a few degrees can double or halve the lethality.

Good to know

This calculator is for learning and for checking arithmetic. A real process must be validated with heat penetration tests at the coldest point of the container, and the temperature and time must follow tested guidelines. Home canning should follow tested recipes from an extension service or a standards body, and never be shortened on the basis of a formula.

The canning altitude calculator adjusts processing for elevation, the pressure cooker calculator converts recipe times, the Newton cooling calculator models how a product loses heat, and the half-life calculator handles the same kind of exponential decay.

Frequently asked questions

What is the F-value?

The F-value is the equivalent time, at a reference temperature, that a heat process delivers. It adds up the lethal effect of the whole process, converted into minutes at the reference temperature. The F0 value of canning uses 121.1 °C (250 °F) and a z-value of 10 °C (18 °F), and is the standard for low-acid foods.

What are the D-value and the z-value?

The D-value is the time at one temperature needed to destroy 90 percent of the organisms, a single log reduction. The z-value is the temperature rise that cuts the D-value by a factor of ten. Together, they describe how fast heat kills a given organism at any temperature.

What is the 12D concept?

In low-acid canning, the process aims for 12 log reductions of Clostridium botulinum spores, which is 12 times the D-value. With a D-value of 0.21 minutes at 250 °F, that is an F0 of about 2.52 minutes. Industry practice uses a larger F0, often 3 minutes or more, for spoilage organisms and safety margin.

Can I use it for pasteurization?

Yes, with other values. Beer pasteurization uses a reference of 60 °C (140 °F) and a z-value of about 7 °C (12.6 °F), where one pasteurization unit is one minute at 60 °C. Other products have their own references. Always use the values given by a validated process, not a guess.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.