Skip to content
Omnikalc

Polytropic process calculator: final volume, temperature, work and heat

Enter the initial state of a gas, the final pressure and the polytropic index to get the final volume, the final temperature, the work, the change of internal energy and the heat exchanged.

Updated on
Your inputs
psia

Value out of range

ft³

Value out of range

°F

Value out of range

psia

Value out of range

Value out of range

Value out of range

Results

Work done on the gas

3,927 ft·lbf

Final volume
0.2288
Final temperature
361.7 °F
Change of internal energy
2,945 ft·lbf
Heat added to the gas (negative if removed)
-982 ft·lbf

A polytropic process is a change of state of a gas that follows p V^n = constant, a model between the isothermal and the adiabatic cases. The polytropic process calculator gives the final volume, the final temperature, the work, the change of internal energy and the heat exchanged by an ideal gas.

How the calculation works

  • Enter the initial pressure (absolute), the initial volume and the initial temperature of the gas, and the final pressure (absolute) that it reaches.
  • Enter the polytropic index n of the process: 0 isobaric, 1 isothermal, γ adiabatic (reversible, no heat), and typically 1.2 to 1.35 for an air compressor with cooling.
  • Enter the heat capacity ratio γ of the gas (1.4 for air and diatomic gases, 1.67 for monatomic gases, 1.3 for steam and CO₂).
  • The calculator applies p V^n = constant and gives the final volume, the final temperature, the work done on the gas, the change of internal energy and the heat exchanged.

Example

Air at 14.7 psia, 1 ft³ and 68 °F is compressed to 100 psia with a polytropic index of n = 1.3 (a cooled compressor). The final volume is 1 × (14.7 / 100)^(1/1.3) = 0.2288 ft³. The final temperature is 527.67 R × (100 × 0.2288) / 14.7 = 821.3 R, or 361.7 °F. The work done on the gas is (100 × 0.2288 − 14.7) / 0.3 × 144 = 3,927 ft·lbf. The internal energy rises by 2,945 ft·lbf, so 982 ft·lbf of heat is removed (heat added is −982 ft·lbf).

Why it matters

The calculator helps thermodynamics and mechanical engineering students and engineers to model the compression or the expansion of a gas in a compressor, a pump, an engine or a cylinder, to size the cooling and to see the effect of the index n. It replaces the manual solution of several equations.

Good to know

Enter the absolute pressure, not the gauge pressure. Check the sign convention: here the work is the work received by the gas, and the heat is positive when it enters. If you get a temperature that seems too high, the index n may be too close to γ: a real compressor with cooling has a lower n. Use the same units for the pressure and the volume.

The ideal gas calculator relates the pressure, volume and temperature, the combined gas law calculator compares two states, the Carnot efficiency calculator gives the ideal limit of a heat engine and the specific gas constant calculator gives R for a gas.

Frequently asked questions

What is a polytropic process?

A polytropic process is a change of state of a gas that follows p V^n = constant, where n is the polytropic index. It is a general model for the real compressions and expansions in compressors, engines and turbines, where the gas exchanges some heat with the walls. Special cases are the isobaric process (n = 0), the isothermal process (n = 1), the adiabatic process (n = γ) and the isochoric process (n → ∞).

How are the results computed?

From the law, V2 = V1 (p1 / p2)^(1/n). For an ideal gas, T2 = T1 (p2 V2) / (p1 V1). The work done by the gas is W = (p1 V1 − p2 V2) / (n − 1) for n ≠ 1, and p1 V1 ln(V2 / V1) for n = 1. The internal energy changes by ΔU = (p2 V2 − p1 V1) / (γ − 1), and the first law gives the heat Q = ΔU + W, the heat added to the gas.

How do I find n from measurements?

Measure the pressure and the volume at two states and compute n = ln(p2 / p1) / ln(V1 / V2). For an air compressor with a water jacket, n is about 1.25 to 1.35. A well-cooled compressor tends toward 1.0 and has the smallest work, while an uncooled one tends toward 1.4. That is why multi-stage compressors with intercoolers are used for high pressures.

What are the limits of the model?

The calculator assumes an ideal gas with a constant heat capacity ratio, a closed system and a reversible process with a constant index n. It does not include the real gas effects at high pressure, the friction, the leaks or the variation of γ with the temperature. Enter the absolute pressures, and for n = γ the heat is zero, which is a useful check.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.