Skip to content
Omnikalc

Meat brine injection calculator

Enter the weight of the meat, the pump percentage and the salt you want in the finished meat to get the brine to inject, the brine strength and the salt and water to mix.

Updated on
Your inputs
lb

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

Results

Brine to inject

1.20 lb

Brine strength needed for the target

14.0 %

Salt for the brine

2.7 oz

Weight of the meat after injection
11.20 lb
Water for the brine
1.03 lb
Salt in the meat with your own brine
1.29 %
Feasible (1 if the brine strength is under 26 % saturation)
1

The meat brine injection calculator gives the weight of brine to inject for a pump percentage, the brine strength needed to reach a target salt in the finished meat, the salt and water to mix, and the salt you get with a brine you already have.

How the calculation works

  • Enter the weight of the meat and the pump percentage.
  • Enter the salt you want in the finished meat and the strength of your brine.
  • Read the brine to inject, the strength needed and the salt and water.

Example

Pumping 10 lb of meat to 12 % takes 1.20 lb of brine, which brings the meat to 11.20 lb. For 1.5 % of salt in the finished meat, the brine must be 14.0 % salt, which means 2.7 oz of salt dissolved in 1.03 lb of water. A brine of 12 % would give 1.29 % of salt in the meat. Feasible: 1.

Why it matters

The calculator helps cooks, pitmasters, butchers and home curers who inject turkeys, hams, pork loins or briskets and want a precise salt level, whether they mix a brine from scratch or work with a ready-made one.

Good to know

Dissolve the salt fully and chill the brine to refrigerator temperature before injecting. Weigh the meat, then weigh it again after the injection to check the real pickup, as the needle often leaves some brine outside. The result assumes that all the injected brine stays in the meat and distributes evenly, and ignores the natural salt of the meat. Brine strengths above 26 percent cannot be dissolved, so a low pump with a high target salt is not feasible. For a cured product, add the nitrite separately and follow tested recipes.

The curing salt calculator doses nitrite, the brine calculator mixes a soaking brine, the dry aged beef calculator estimates trim and loss and the cooked to raw weight calculator converts the weight of meat after cooking.

Frequently asked questions

What is the pump percentage?

It is the weight of brine injected, as a percentage of the weight of the raw meat. A pump of 10 percent means that 10 pounds of meat receive 1 pound of brine. Hams are commonly pumped at 10 to 30 percent, poultry and pork loins at 8 to 15 percent. The more brine, the juicier the meat, but too much gives a watery product.

How do you compute the brine strength?

The salt of the brine ends up spread through the meat plus the brine. So the salt percentage in the finished meat is the strength of the brine multiplied by the pump, divided by 100 plus the pump. To reach a target, the brine must have a strength equal to the target multiplied by 100 plus the pump, divided by the pump. A low pump therefore needs a strong brine.

How much salt is a good level?

Most cured and brined meats contain 1.2 to 2 percent salt in the finished product. Below this, the taste is flat and the preservation is weaker. Above 2.5 percent it is salty for most people. Start at the lower end if you are unsure, since you can always salt at the table.

Is this enough for a cured meat?

No. A cured ham or bacon also needs sodium nitrite from a curing salt, at a controlled level, for safety. This calculator only manages the salt. Use the curing salt calculator for the nitrite and follow the tested recipes. Keep the meat cold during and after the injection, and cook or cure it as required.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.