Skip to content
Omnikalc

Injection molding cooling time calculator: how long must a plastic part cool in the mold?

Enter the plastic, the wall thickness and the temperatures to get the cooling time, the cycle time and the shots per hour.

Updated on
Your inputs
in

Value out of range

°F

Value out of range

°F

Value out of range

°F

Value out of range

s

Value out of range

Results

Cooling time

10.6 s

Total cycle time
22.6 s
Shots per hour
159
Share of the cycle spent cooling
47.0 %
Cooling time if the wall were 25 % thicker
16.6 s

The longest step of an injection molding cycle is waiting for the plastic to cool enough to be ejected, and it depends mostly on the wall thickness. The injection molding cooling time calculator takes the plastic, the wall thickness and the melt, mold and ejection temperatures, with the other cycle time, and gives the cooling time, the total cycle time, the shots per hour, the share of the cycle spent cooling and the cooling time for a wall 25 % thicker.

How the calculation works

  • Choose the plastic, which sets a typical thermal diffusivity, and enter the wall thickness of the part.
  • Enter the melt temperature, the mold wall temperature and the ejection temperature, at which the part is stiff enough to leave the mold.
  • The cooling time of a flat wall is t = h² / (π² α) × ln[ (4/π) × (Tmelt − Tmold) / (Teject − Tmold) ].
  • Enter the other cycle time to get the total cycle, the shots per hour and the share of the cycle spent cooling.

Example

An ABS part has a wall of 0.1 in (2.54 mm), melt at 446 °F, mold at 122 °F and ejection at 203 °F. The log term is ln(4/π × 324 / 81) = 1.628, and the cooling time is 2.54² / (π² × 0.10) × 1.628 = 10.6 s. With 12 s for the rest of the cycle, the cycle is 22.6 s, which is 159 shots per hour, and cooling takes 47 % of it. A wall 25 % thicker would need 16.6 s.

Why it matters

Cooling time drives the cost of a molded part, so designers try to keep walls thin and even and processors tune temperatures. A quick estimate helps to quote a cycle time, to compare materials and wall designs, and to see how much a thickness reduction could save before the mold is cut.

Good to know

The thermal diffusivity values are typical and round, and real materials vary with grade, filler and temperature. The formula covers a flat wall cooled on both sides and ignores ribs, bosses, the cooling channel layout, the fill and pack time, the contact resistance and the change of properties with temperature. Mold flow software and trials give the actual cooling time.

The heat conduction calculator covers heat flow through a solid, the latent heat calculator covers phase changes, the heat sink calculator sizes cooling, and the thermal expansion calculator covers dimension changes with temperature.

Frequently asked questions

Why is the cooling time so important?

Cooling is the longest part of the molding cycle, often 50 to 80 % of it, so it sets the output of the machine and the cost per part. A part that is ejected too hot warps or sinks, and one that is cooled too long wastes time. The cooling time grows with the square of the wall thickness, so wall thickness is the strongest lever.

What does the formula assume?

It comes from the solution of transient heat conduction in a flat plate of constant thickness with both faces held at the mold temperature, taking the first term of the series. The temperature that matters is the centre of the wall, which is the last to cool. The result is for a uniform wall and a constant mold temperature.

What is the ejection temperature?

It is the average or centre temperature at which the part is stiff enough to be pushed out without distortion, often close to the heat deflection temperature of the plastic. The value depends on the material and the geometry, and a lower ejection temperature gives a longer cooling time, but a more stable part.

How can I cut the cooling time?

Make walls thinner and more uniform, lower the mold temperature within the limits for surface finish and flow, use materials with a higher diffusivity, add conformal cooling channels, and raise the ejection temperature if the part stays stable. The 25 % thicker wall in the results shows why even small increases in thickness cost a lot of time.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.