Skip to content
Omnikalc

Paracord bracelet calculator: how much cord do I need?

Enter your wrist size, the buckle, the weave and the cord thickness to get the length of cord for one paracord bracelet and the number you can make from a hank.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

mm

Value out of range

Value out of range

Results

Total cord for one bracelet

7.38 ft

Finished bracelet length
7.50 in
Length of the woven part
6.50 in
Working cord
6.50 ft
Core cord
0.88 ft
Bracelets from one hank
13

Cutting too little paracord means starting again, and too much wastes the hank. This paracord bracelet calculator takes the wrist size, the comfort allowance, the buckle, the weave and the cord diameter to give the finished length, the woven length, the working cord, the core cord, the total cord and the number of bracelets per hank.

How the calculation works

  • Finished length = wrist circumference + extra length for comfort. Woven part = finished length − the length of the buckle.
  • Working cord = woven length × a weave factor in feet per inch × diameter ÷ 4 mm. A cobra weave takes about 1 foot of cord per inch, a king cobra about 2 feet and a fishtail about 1.5 feet, for standard 4 mm cord.
  • Core cord = woven length + 4 inches, the straight piece that the weave covers, with a little extra to tie off.
  • Total cord = working cord + core cord. Bracelets per hank = hank length ÷ total, rounded down.

Example

A wrist of 7 in with 0.5 in of comfort gives a finished length of 7.5 in. With a 1 in buckle the woven part is 6.5 in. A cobra weave in 4 mm cord needs 6.5 × 1 = 6.5 ft of working cord, and the core is 6.5 + 4 = 10.5 in, or 0.88 ft. The total is 7.38 ft, so a 100 ft hank makes 13 bracelets.

Why it matters

Paracord bracelets are popular for camping, gifts and craft fairs. Knowing the length in advance lets you cut the cord with some margin, plan a batch from a 100 ft hank and price the materials if you sell your work.

Good to know

Always add a spare inch or two before cutting, since a tight weave uses more cord and a first attempt often does. Melt the ends with a lighter to stop fraying and do it with care, away from the face and flammable things. Do not rely on a decorative bracelet as safety gear. The calculator is for 550 type cord, and you can enter another diameter, but the weave factors are only a guide.

The macrame cord calculator sizes cord for wall hangings and plant hangers and the string art calculator plans the thread for a design.

Frequently asked questions

How much paracord does a bracelet need?

A common rule is about one foot of cord for every inch of the woven part for a cobra weave, plus some for the core. A 7 inch wrist therefore takes roughly 7 to 8 feet in all. Thicker cord, a tighter weave or a looser one change the amount, so make a spare inch or two of room for the first try.

Why does the weave change the length?

A king cobra is a cobra woven twice with a second layer, so it takes about twice as much cord. A fishtail is flatter and takes a bit more than a cobra for the same length. These factors are rules of thumb and your tension changes them, so tie a trial piece before you cut a long cord.

How do I measure the wrist?

Wrap a tape or a string around the wrist where the bracelet will sit, just below the wrist bone, and add half an inch for comfort. The bracelet should slide over the hand when it is closed and not pinch. Remember that a buckle takes up some of the finished length, which is why the woven part is shorter.

What is the core cord?

The core is a straight piece that runs through the middle of the weave and carries the buckle. It is covered by the knots, so it is not seen, but it keeps the bracelet from stretching. It needs only the length of the woven part plus a few inches to tie the ends.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.