Skip to content
Omnikalc

Siphon calculator: flow rate, draining time and crest pressure

Enter the height drop, the crest height, the hose diameter and the losses of a siphon to get the velocity, the flow rate, the time to drain a tank and the pressure at the highest point.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

in

Value out of range

Value out of range

gal

Value out of range

Results

Flow rate

11.8 gpm

Velocity in the hose
8.58 ft/s
Time to drain the volume
4:39
Absolute pressure at the crest
12.90 psi
Safe pressure at the crest
Highest crest before the water boils
32.0 ft

A siphon moves a liquid over a high point with no pump, thanks to the height drop and the atmospheric pressure. The siphon calculator gives the velocity and the flow rate in the hose, the time to drain a tank and the pressure at the crest, to check that the siphon will not break.

How the calculation works

  • Enter the height drop between the water surface in the tank and the outlet of the hose, and the height of the crest (the highest point of the hose) above the water surface.
  • Enter the inside diameter of the hose and the total loss coefficient K, the sum of the entry loss (about 0.5), the exit loss (1.0), the bends and the friction. A short hose usually has K from 2 to 4.
  • Enter the volume to drain.
  • The velocity comes from the energy balance v = √(2 g H / (1 + K)). Read the velocity, the flow rate, the draining time, the pressure at the crest and the highest crest that is possible.

Example

A hose of 0.75 in inside diameter drains a tank with a drop of 4 ft and a crest 3 ft above the water, with K = 2.5. The velocity is √(2 × 32.17 × 4 / 3.5) = 8.58 ft/s. The hose area is 0.00307 ft², so the flow rate is 11.8 gpm, and it takes 4 min 39 s to drain 55 gal. The absolute pressure at the crest is 14.7 − 62.4 × (3 + 1.14) / 144 = 12.90 psi, safe. The highest crest possible before the water boils is 32.0 ft.

Why it matters

The calculator helps gardeners, aquarium keepers, boaters, brewers, farmers and students to know how long it takes to drain a tank, a pool, a barrel or a pond with a hose, and how high the hose may rise. It also explains why a bigger hose or a longer drop speeds the flow so much.

Good to know

Use the largest hose that is practical, keep it short, avoid sharp bends and keep the crest as low as possible. Make the outlet lower than the water surface by as much as you can, since the flow grows with the square root of the drop. Use a clear hose, so you can see air bubbles, and be careful when siphoning dangerous liquids, such as fuel, never by mouth.

The tank drain time calculator treats the draining of a tank through a hole, the Bernoulli calculator gives the energy balance of a flow, the pipe flow velocity calculator links the flow and the diameter, and the hydrostatic pressure calculator gives the pressure of a column of liquid.

Frequently asked questions

How does a siphon work?

A siphon moves a liquid over a high point with no pump. Once the hose is full, the weight of the liquid in the longer, lower leg pulls the liquid in the hose, and the atmospheric pressure pushes more liquid from the tank in the shorter leg. The flow depends on the height drop between the surface of the tank and the outlet, not on the height of the crest.

What is the flow velocity?

From Bernoulli's equation with the losses, the velocity is v = √(2 g H / (1 + K)), where H is the drop between the surfaces (or the outlet), and K the sum of the loss coefficients in the hose. Without losses, it is the Torricelli velocity √(2 g H). A narrow or long hose with bends has a larger K and so a lower flow.

How high can the crest be?

The pressure at the crest is lower than the atmospheric pressure by the weight of the column of water, ρ g × (crest height + v² / 2g). When it falls to the vapor pressure of the water, about 0.34 psi (2.3 kPa) at 20 °C, the water boils or the dissolved air comes out, and the siphon stops. In theory the limit is about 32 ft (10 m) at sea level, but in practice keep the crest below 20 ft (6 m).

Why does my siphon not start or stop?

A siphon stops if air gets into the hose, if the inlet comes out of the water, or if the crest is too high. It does not start if the hose is not full of liquid. Fill the hose first, or suck on the end, or immerse it fully. At the end of the drain, when the level reaches the inlet, the air enters and the flow stops. The calculator gives an ideal steady flow.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.