Skip to content
Omnikalc

Steady-state accumulation calculator: how high do repeated doses build up?

Enter the half-life, dosing interval, dose, volume of distribution and bioavailability to get the accumulation factor and the peak, trough and average concentrations.

Updated on

Educational tool, not medical advice: this page does not diagnose and does not replace a doctor, nurse or pharmacist. It has not been reviewed by a healthcare professional. Editorial and medical policy

Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

Value out of range

Results

Peak concentration at steady state (mg/L)

4.950

Accumulation factor R
1.547
Trough concentration at steady state (mg/L)
1.750
Average concentration at steady state (mg/L)
3.078
Time to reach 90 % of steady state (hours)
26.6

This calculator is for general information and education. It is not medical advice and does not replace the advice of your doctor or a registered dietitian.

When a drug is given at regular intervals, each dose adds to what is left from the previous ones until the levels level off. The steady-state accumulation calculator takes the half-life, the dosing interval, the dose, the volume of distribution and the bioavailability, and gives the accumulation factor, the peak, trough and average concentrations at steady state and the time to reach 90 %.

How the calculation works

  • From the half-life, compute the elimination rate constant k = ln 2 ÷ t½.
  • The accumulation factor for repeated doses at interval τ is R = 1 ÷ (1 − e^(−k × τ)). It says how many times higher the steady-state peak is than the peak after the first dose.
  • The first-dose peak is F × dose ÷ Vd. The steady-state peak is that value times R, and the trough is the peak times e^(−k × τ).
  • The average concentration is F × dose ÷ (CL × τ), with clearance CL = k × Vd. Steady state is reached after about 3.3 half-lives for 90 %, whatever the dose.

Example

A drug with a half-life of 8 hours is given every 12 hours at 200 mg, with a volume of distribution of 50 L and a bioavailability of 0.8. Then k = 0.0866 per hour and R = 1 ÷ (1 − e^(−1.04)) = 1.547. The first-dose peak is 3.2 mg/L, so the steady-state peak is 4.95 mg/L and the trough is 1.75 mg/L. The average is 3.08 mg/L, and 90 % of steady state is reached after about 26.6 hours.

Why it matters

Dosing regimens are designed around accumulation. Pharmacology students and researchers use this calculation to see how the interval changes the peak and the trough, and to understand why some drugs need days to reach their full effect.

Good to know

The model has one compartment, first-order elimination and intravenous-like absorption, so it ignores the delay and the shape of absorption after oral doses. The peak is taken right after the dose. Use it to learn and to compare regimens, not to set a dose for a real patient.

The half-life calculator shows how a single dose falls over time, and the child medicine dose calculator shows weight-based dosing.

Frequently asked questions

What is steady state?

It is the point at which the amount of drug given in each interval equals the amount eliminated, so the concentrations repeat from dose to dose. Peaks and troughs stay the same instead of climbing. It is reached after about four to five half-lives, however large the dose is.

What does the accumulation factor mean?

It compares the steady-state level with the level after a single dose. When the interval equals the half-life, R is 2. When the interval is much shorter than the half-life, R is large, and when it is much longer, R is close to 1 and the drug barely accumulates.

How can I reduce the gap between peak and trough?

Give smaller doses more often. The average concentration stays the same if the daily total is the same, but the peak falls and the trough rises. Long-acting formulations achieve the same by releasing the drug slowly.

Why does it take the same time whatever the dose?

The time to steady state depends on the half-life only. A bigger dose raises the levels in proportion but does not make them get there sooner. A loading dose is the way to reach the target level earlier.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.