Skip to content
Omnikalc

Alkalinity titration calculator: how well is your water buffered?

Enter the sample volume, the acid normality and the acid volume used to reach pH 4.5 to get the total alkalinity in mg/L as CaCO3, meq/L, dKH and bicarbonate.

Updated on
Your inputs
mL

Value out of range

N

Value out of range

mL

Value out of range

Results

Total alkalinity

36.0 mg/L as CaCO₃

Alkalinity in a common range for drinking water, pools and aquariums
Alkalinity in milliequivalents
0.72 meq/L
Carbonate hardness (KH)
2.02 °dKH
Bicarbonate equivalent
43.9 mg/L HCO₃⁻

Alkalinity tells how much acid water can absorb before its pH falls. The alkalinity titration calculator converts a titration to pH 4.5 into the total alkalinity in mg/L as CaCO₃, in meq/L, in carbonate hardness (°dKH) and in bicarbonate, from the sample volume, the acid normality and the acid volume.

How the calculation works

  • Enter the volume of the water sample, the normality of the standard acid (0.02 N sulfuric acid is common) and the volume of acid needed to bring the sample to pH 4.5.
  • The total alkalinity is A = V_acid × N × 50,000 / V_sample, in mg/L as calcium carbonate (CaCO₃).
  • The calculator also gives it in milliequivalents per liter and as carbonate hardness, in German degrees (°dKH), the unit used in aquariums.
  • The bicarbonate equivalent is the mass of HCO₃⁻ that has the same acid-neutralizing capacity.

Example

A 100 mL sample of tank water needs 3.6 mL of 0.02 N acid to reach pH 4.5. The alkalinity is 3.6 × 0.02 × 50,000 / 100 = 36.0 mg/L as CaCO₃, which is 0.72 meq/L, 2.02 °dKH and the equivalent of 43.9 mg/L of bicarbonate. That is a soft, weakly buffered water.

Why it matters

Alkalinity is measured in drinking-water plants, in pools, in aquariums, in boilers, in wastewater treatment and in agriculture. It decides how much acid or base is needed to change the pH, how corrosive or scaling the water is, and whether a biological process, such as nitrification, has enough buffering.

Good to know

The calculator assumes a titration with a strong acid to pH 4.5, and a total alkalinity expressed as CaCO₃, where 1 meq/L is 50 mg/L. The conversion to bicarbonate is exact only when the whole alkalinity is bicarbonate, which is the case for a pH under 8.3. Organic acids, phosphates, borates and silicates also contribute to the alkalinity of some waters. For a precise value, use a calibrated pH meter and a standardized acid, and note the temperature.

The titration calculator covers the general acid–base titration, the water hardness calculator converts hardness units, the aquarium CO₂ calculator uses the alkalinity with the pH to find the dissolved CO₂, and the pKa ionization calculator covers the weak acids behind the buffering.

Frequently asked questions

What is alkalinity?

Alkalinity is the capacity of water to neutralize acid, to resist a fall of the pH. In most natural waters it comes from bicarbonate, carbonate and hydroxide ions, mostly from the dissolution of limestone. It is not the same as pH, which says how acid or basic the water is at this moment, but it decides how stable the pH is.

Why is pH 4.5 the end point?

At pH 4.5, practically all the bicarbonate and carbonate have been converted to carbonic acid. This is the usual end point of the total alkalinity titration, with an indicator (bromocresol green–methyl red) or a pH meter. For waters with a pH above 8.3, the phenolphthalein alkalinity, to pH 8.3, is also measured to find the carbonate.

What is the difference between alkalinity and hardness?

Alkalinity is about the anions that neutralize acid, while hardness is about the calcium and magnesium cations. They are often close in a limestone water, where both come from dissolved CaCO₃, but they are not the same. Carbonate hardness (KH) is the part of the hardness that matches the alkalinity, and the aquarium world uses the two names for the same measurement.

What values are good?

Drinking water is usually 30 to 200 mg/L. A swimming pool is kept at 80 to 120 mg/L, a freshwater aquarium at 3 to 8 °dKH (50 to 140 mg/L), and a reef tank at 7 to 11 °dKH. Below 20 mg/L, the water is poorly buffered and the pH can crash; above 200 mg/L, it is hard to lower the pH and scale forms.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.