Skip to content
Omnikalc

BSFC calculator: how efficiently does your engine turn fuel into power?

Enter the brake power, the fuel flow and the fuel to get brake specific fuel consumption in lb/hp·h and g/kWh, the fuel mass flow and the brake thermal efficiency.

Updated on
Your inputs
hp

Value out of range

gal/h

Value out of range

Results

Brake specific fuel consumption

0.379 lb/hp·h

Brake thermal efficiency

36.5%

Usual range for an engine
Fuel mass flow
56.8 lb/h
BSFC in grams per kilowatt-hour
230 g/kWh

BSFC tells you how much fuel an engine burns for each unit of power it delivers, and it is the standard figure for comparing engines. This BSFC calculator takes the brake power, the fuel flow and the fuel type to give the brake specific fuel consumption in pounds per horsepower-hour and grams per kilowatt-hour, the fuel mass flow and the brake thermal efficiency.

How the calculation works

  • Fuel mass flow = fuel flow in gallons per hour × fuel density in pounds per gallon.
  • BSFC = fuel mass flow ÷ brake power, in pounds per horsepower-hour. Multiply by 608.277 for grams per kilowatt-hour.
  • Brake thermal efficiency = 2,544.43 Btu per horsepower-hour ÷ (BSFC × fuel heating value) × 100.
  • Heating value used: 18,400 Btu per pound for diesel and 18,700 Btu per pound for gasoline.

Example

A diesel engine delivers 150 hp at the brake while burning 8 gal/h. At 7.1 lb per gallon the mass flow is 56.8 lb/h, so BSFC is 56.8 ÷ 150 = 0.379 lb/hp·h, or 230 g/kWh. With a heating value of 18,400 Btu/lb the thermal efficiency is 2,544.43 ÷ (0.379 × 18,400) = 36.5 %.

Why it matters

Engine designers, boat and aircraft owners, generator operators and race teams use BSFC to compare engines, to tune the mixture and to size fuel tanks. A drop of 10 g/kWh over thousands of hours is a large fuel saving, and the efficiency figure shows how close the engine comes to the limit set by the laws of thermodynamics.

Good to know

The measurement must be made at steady state, with the power and the fuel flow taken at the same time, because a transient load gives a meaningless result. Fuel density changes with temperature and the blend, so the values here are typical, and the heating value used for efficiency is the lower heating value. Ethanol blends have a lower energy per gallon, so their BSFC is higher even when the engine is not less efficient. Indicated and brake figures differ, since friction takes 10 % or more of the power.

The gas mileage calculator measures fuel per distance, the horsepower and torque calculator relates power to torque and rpm and the Carnot efficiency calculator gives the theoretical limit for a heat engine.

Frequently asked questions

What is BSFC?

Brake specific fuel consumption is the fuel an engine burns per unit of power produced at the crankshaft in an hour. A lower value means a more efficient engine.

What is a good BSFC?

Modern diesel engines reach 0.32 to 0.40 lb/hp·h (195 to 245 g/kWh) and gasoline engines 0.40 to 0.55 lb/hp·h (245 to 335 g/kWh) at their best point. Large slow marine diesels go below 0.30.

How do I get brake power?

Brake power is measured on a dynamometer at the crankshaft or the flywheel, or taken from the engine data sheet at the operating speed and load. It is lower than the indicated power inside the cylinders.

Why does BSFC change with load?

An engine is least efficient at light load, because friction and pumping losses take a larger share, and most efficient at about 70 to 85 % of the full load at a moderate speed. A BSFC map shows the whole range.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.