Skip to content
Omnikalc

How much power does a given torque and rpm deliver?

Enter the torque, engine speed, drivetrain loss and displacement: get horsepower, kilowatts, metric horsepower, wheel horsepower and specific output per liter.

Updated on
Your inputs

Value out of range

rpm

Value out of range

%

Value out of range

Value out of range

Results

Engine power (mechanical horsepower)

366.5

Specific output in the usual range for a modern engine
Power in kilowatts
273.3
Metric horsepower (PS)
371.6
Estimated horsepower at the wheels
311.5
Specific output (hp per liter)
73.3

Horsepower and torque are two views of the same thing. Torque is the twisting force the engine delivers; power is the rate at which it does work, and it equals torque multiplied by engine speed. This calculator converts a torque figure at a given rpm into horsepower, kilowatts and metric horsepower, estimates the power that reaches the wheels, and gives the specific output per liter of displacement.

How the calculation works

  • Power (kW) = torque (N·m) × rpm × 2π ÷ 60 ÷ 1,000
  • Horsepower = kW ÷ 0.7457, which is torque (lb-ft) × rpm ÷ 5,252
  • Metric horsepower (PS) = kW ÷ 0.7355
  • Wheel power = engine power × (1 − drivetrain loss)
  • Specific output = horsepower ÷ displacement in liters

Example

An engine delivers 350 lb-ft at 5,500 rpm with a 5.0 liter displacement and 15% drivetrain loss. That is 474.5 N·m, a power of 273.3 kW or 366.5 hp (371.6 PS). About 311.5 hp reaches the wheels, and the specific output is 73.3 hp per liter.

Why it matters

Comparing engines, reading dyno charts and checking a manufacturer’s claims all rely on the link between torque, speed and power. A high torque at low rpm gives strong pulling, while the same power at higher rpm calls for lower gearing. The specific output shows how hard an engine is worked.

Good to know

The 15% loss is a typical figure, not a measurement, and real losses vary with gearbox, temperature and load. Engine ratings follow different standards (SAE, DIN, ECE), so figures from different countries can differ by a few percent. Torque also depends on the fuel, the air temperature and the altitude, which is why dyno figures are usually corrected to standard conditions. This tool is for education and does not replace a dyno test.

The torque calculator computes torque from force and lever arm, the quarter-mile calculator estimates acceleration from power and weight, and the gear ratio calculator gives output speed and torque of a gear train.

Frequently asked questions

How are horsepower and torque related?

Power is torque multiplied by rotational speed. In imperial units, horsepower = torque in lb-ft × rpm ÷ 5,252. That is why the torque and power curves cross at 5,252 rpm on a dyno chart.

What is the difference between hp, PS and kW?

Mechanical horsepower (hp) equals 745.7 watts. The metric horsepower (PS, ch or CV) equals 735.5 watts. One kilowatt is about 1.341 hp or 1.360 PS.

Why is wheel horsepower lower than engine horsepower?

The gearbox, driveshaft and differential absorb part of the power as friction. Losses of 10 to 15 percent are common for a rear-wheel drive car with a manual gearbox and a little more for four-wheel drive or automatics.

Does the result apply to the whole rev range?

No. Torque varies with rpm, so the result is the power at the rpm you entered, not the maximum power of the engine. Use the torque at the peak-power rpm for the rated figure.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.