Skip to content
Omnikalc

Characteristic impedance calculator: size a transmission line for 50 or 75 ohms

Choose a coaxial cable, a twin-lead or a microstrip, enter its dimensions and dielectric constant, and get the characteristic impedance, velocity factor, delay, inductance and capacitance per meter.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

Value out of range

Results

Characteristic impedance Z₀

51.10 Ω

Close to the 50 Ω standard of radio and test equipment
Effective relative permittivity
2.300
Velocity factor
0.6594
Propagation delay
5.059 ns/m
Inductance per meter
258.5 nH/m
Capacitance per meter
99.0 pF/m

A transmission line carries a signal without reflection only if it is terminated by its characteristic impedance. The characteristic impedance calculator gives the Z₀ of a coaxial cable, a twin-lead or a microstrip from its dimensions and the dielectric constant, with the velocity factor, the delay and the inductance and capacitance per meter.

How the calculation works

  • Choose the type of line: coaxial cable, twin-lead or microstrip on a circuit board.
  • Enter the two dimensions of the line in the same unit and the relative permittivity εr of the dielectric.
  • For a coaxial cable, Z₀ = (60 / √εr) ln(D / d). For twin-lead in air, Z₀ = (120 / √εr) arcosh(s / d).
  • For a microstrip, the calculator uses the formula of Hammerstad with the effective permittivity εeff, which lies between that of the board and that of air. The result also gives the velocity factor, the delay and the L and C per meter.

Example

A coaxial cable with a dielectric of diameter D = 2.95 mm, an inner conductor of d = 0.81 mm and a polyethylene dielectric (εr = 2.3) has Z₀ = 59.96 / √2.3 × ln(2.95 / 0.81) = 51.10 Ω. The velocity factor is 0.6594, the delay 5.059 ns/m, and the cable has 258.5 nH/m and 99.0 pF/m. This is the geometry of RG-58, a 50 Ω cable.

Why it matters

The impedance of the line decides whether a radio, a video link or a high-speed digital board works well. The calculator is useful to choose a cable, to design the width of a trace on a circuit board and to check the geometry of a homemade feedline for an antenna.

Good to know

The formulas are for lines without losses, with a uniform dielectric (coaxial and twin-lead) and for a microstrip of negligible copper thickness on an infinite ground plane. The real impedance of a microstrip changes by a few ohms with the thickness of the trace, the solder mask and the frequency, and the permittivity of the board changes with frequency and with the weave of the glass. For critical designs, use the field solver of the board manufacturer. The twin-lead is computed for two round wires of the same diameter in a uniform dielectric.

The coax electrical length calculator cuts a cable to a given phase, the SWR calculator shows the effect of a mismatch on the reflections, the RLC impedance calculator covers lumped circuit elements, and the LC resonance calculator covers tuned circuits.

Frequently asked questions

What is the characteristic impedance?

It is the ratio of the voltage to the current of a wave that travels on a transmission line, Z₀ = √(L/C) for a line without losses. It depends only on the geometry of the line and the dielectric, not on its length. A signal sees the line as a resistor of value Z₀ until the end of the line is reached, and a load that matches Z₀ absorbs all the power with no reflection.

Why 50 and 75 ohms?

For a coaxial cable with an air dielectric, the lowest loss is at 77 Ω and the highest power capacity is at 30 Ω. The compromise, 50 Ω, became the standard for radio and test equipment, and 75 Ω, close to the minimum loss for polyethylene, the standard for video, cable TV and antennas for broadcast. Twin-lead has a high impedance, 300 Ω for old television antennas.

How does a microstrip differ?

The field of a microstrip is partly in the board and partly in the air above, so the signal travels at a speed that corresponds to an effective permittivity between 1 and εr. For a 50 Ω line on FR-4 (εr = 4.4), the width is about twice the thickness of the board. A narrower trace gives a higher impedance. The thickness of the copper and the solder mask also change the result by a few percent.

What are the velocity factor and the delay?

The velocity factor is the speed of the wave in the line divided by the speed of light, 1/√εeff. It is 0.66 for solid polyethylene, 0.85 or more for foam, and about 0.55 for FR-4 microstrip. The delay in ns/m is its inverse. Both are needed to cut a cable to a given electrical length, or to match the lengths of the traces on a fast digital board.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.