Skip to content
Omnikalc

Colpitts oscillator calculator

Enter the inductance, the two capacitors and the transistor gain to get the oscillation frequency, the feedback ratio and the margin for the oscillation to start.

Updated on
Your inputs
µH

Value out of range

pF

Value out of range

pF

Value out of range

mS

Value out of range

kΩ

Value out of range

Results

Oscillation frequency

5.543 MHz

Minimum voltage gain to start (C2 / C1)

4.70

Equivalent series capacitance
82.46 pF
Period
180.4 ns
Feedback ratio C1 / (C1 + C2)
0.175
Available gain gm × R
40.0
Start-up margin (available ÷ required)
8.51
Oscillation starts (1 yes, 0 no)
1

The Colpitts oscillator calculator gives the oscillation frequency, the period, the equivalent capacitance, the feedback ratio, the minimum gain to start, the available gain and the start-up margin, from L, C1, C2 and the transistor stage.

How the calculation works

  • Enter the inductance L in microhenries and the capacitors C1 and C2 in picofarads.
  • Enter the transconductance of the transistor and the collector load resistance.
  • Read the frequency and check that the start-up margin is above 1, preferably 2 to 5.

Example

With 10 µH, 100 pF and 470 pF, the equivalent capacitance is 82.46 pF and the oscillator runs at 5.543 MHz, a period of 180.4 ns. The feedback ratio is 0.175 and the required gain 4.70. The stage offers 40.0, a margin of 8.51, so the oscillation starts (1).

Why it matters

The calculator helps electronics students, radio amateurs and engineers who design RF and VFO oscillators, test equipment and signal sources, and who want to choose L, C1 and C2 for a target frequency and to check that the amplifier has enough gain for the oscillation to start.

Good to know

Use the real values of the components, including the tolerance of the capacitors, and remember that the transistor, the wiring and the load add stray capacitance that lowers the frequency, especially above a few tens of megahertz. The start-up gain formula is an approximation for a common-base or common-emitter stage, and the exact condition depends on the bias, the loading and the losses of the inductor. Simulate and measure the circuit, and use a buffer stage to reduce the pulling of the frequency by the load.

The LC resonance calculator gives the resonant frequency of a tank, the crystal load capacitor calculator handles quartz oscillators, the RLC impedance calculator covers the impedance of the tank and the Sallen–Key filter calculator designs active filters.

Frequently asked questions

How does a Colpitts oscillator work?

A Colpitts oscillator is an LC oscillator in which a capacitive divider made of two capacitors in series, C1 and C2, feeds back part of the output voltage to the amplifier input, in a loop with a total phase shift of 360 degrees. The inductor and the two capacitors form the resonant tank that sets the frequency.

What is the oscillation frequency?

The frequency is f = 1 / (2π √(L × Ceq)), where Ceq = C1 C2 / (C1 + C2) is the series combination of the two capacitors. It is the same as the resonant frequency of an LC circuit with the equivalent capacitance, and it is slightly modified by the transistor capacitances and by the load.

What gain is needed for the oscillation to start?

For a common-base or common-emitter stage, the loop gain must be at least one. With the feedback ratio C1 / (C1 + C2), a common approximation is that the voltage gain of the amplifier must exceed C2 / C1. In practice, a margin of 2 to 5 is used to ensure start-up, and amplitude is then limited by the nonlinearity of the transistor.

How does it compare with the Hartley oscillator?

The Hartley oscillator uses a tapped inductor or two inductors and a single capacitor, while the Colpitts uses a tapped capacitor and a single inductor. The Colpitts has a better waveform at high frequency because the capacitors pass the harmonics better, and it is easier to build without a tapped coil.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.