Skip to content
Omnikalc

Corner weights and cross weight calculator

Enter the four scale readings of a vehicle to get the total weight, the front, rear, left and right percentages, the cross weight percentage and the weight to move to balance it.

Updated on
Your inputs
lb

Value out of range

lb

Value out of range

lb

Value out of range

lb

Value out of range

Results

Total weight

2,870 lb

Front axle share

55.1 %

Left side share

49.5 %

Cross weight (right front + left rear)

50.87 %

Rear axle share
44.9 %
Right side share
50.5 %
Cross weight away from 50 %
0.87 %
Weight to move on the diagonal to reach 50 % (positive: add to the right front and left rear)
-12.5 lb

The corner weights and cross weight calculator takes the four scale readings of a vehicle and gives the total weight, the front, rear, left and right percentages, the cross weight percentage and the weight to move on the diagonal to bring the cross weight to 50 percent.

How the calculation works

  • Weigh each wheel on a scale with the vehicle level, and enter the four corner weights.
  • Read the total and the axle and side percentages.
  • Read the cross weight and the weight to move to balance it.

Example

The four corners weigh 770 lb, 810 lb, 650 lb and 640 lb, a total of 2,870 lb. The front axle carries 55.1 % and the rear 44.9 %. The left side carries 49.5 % and the right 50.5 %. The cross weight is 50.87 %, which is 0.87 % away from 50 percent; moving -12.5 lb along the diagonal balances it.

Why it matters

The calculator helps racers, builders of kit and hot-rod cars, trailer and camper owners and mechanics who set up a vehicle on corner-weight scales, and want to check the balance of a car after changes in springs, fuel or driver.

Good to know

Weigh on a flat, level surface with the tires at their working pressure and the vehicle loaded the way it will be used, with the driver and a typical amount of fuel. Release the brakes and roll the vehicle back and forth before each reading to settle the suspension, and remove any anti-roll bar link to avoid false readings. The scales must be calibrated. The cross weight changes with every adjustment, so repeat the weighing after each change of ride height.

The tongue weight calculator sets the load on a hitch, the vehicle payload calculator adds the cargo, the center of mass calculator locates the balance point and the longitudinal weight transfer calculator shows the effect of braking.

Frequently asked questions

What are corner weights?

They are the loads carried by each of the four tires, measured by placing each wheel on its own scale with the car level and the driver inside, if the car will be driven that way. They show how the weight is distributed and are used in racing to balance the car, but also in trailers, campers and kit cars to check the set-up.

What is the cross weight?

Cross weight, or wedge, is the sum of the weights on one diagonal, the right front and left rear, as a percentage of the total. A balanced car has a value of 50 percent when the left and right sides are equal. A different value makes the car turn better in one direction than the other, so racers adjust it for the type of track.

How can the cross weight be changed?

On a car with adjustable coil-over springs, you change the spring height at one corner by turning the jack bolt or the spring perch. Raising the right front also loads the left rear, and unloads the left front and right rear. The calculator gives the weight to shift to equalize both diagonals. After an adjustment, roll the car and weigh it again.

What is a good left-right balance?

For a road car, the left and right sides should be within about 1 percent. For a track car running mostly left turns, a small bias is sometimes wanted. A big imbalance may indicate a bent chassis, a sagging spring, or a load that is not centered, such as a heavy driver or a fuel tank on one side.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.