Skip to content
Omnikalc

CPU dynamic power calculator: how much power do you save by lowering voltage and frequency?

Enter the activity factor, the capacitance, the voltage, the frequency and the leakage to get the dynamic and total power and the effect of voltage and frequency scaling.

Updated on
Your inputs

Value out of range

nF

Value out of range

V

Value out of range

GHz

Value out of range

W

Value out of range

V

Value out of range

GHz

Value out of range

Results

Dynamic power at the current setting

65.3 W

Total power at the current setting
77.3 W
Total power at the new voltage and frequency
51.3 W
Total power saved
33.7 %
Relative performance at the new frequency
80.6 %
Energy per task saved
17.7 %

Most of the power a processor burns comes from switching its transistors, and it depends on the voltage far more than on anything else. The CPU dynamic power calculator takes the activity factor, the switched capacitance, the supply voltage, the clock frequency and the leakage power, and gives the dynamic power, the total power, the total power at a new voltage and frequency, the power saved, the relative performance and the energy saved per task.

How the calculation works

  • Enter the activity factor (the share of the capacitance that switches each cycle), the total switched capacitance, the supply voltage and the clock frequency.
  • Enter the static power from leakage, which does not depend on the clock.
  • The dynamic power is P = α × C × V² × f. The calculator adds the static power to get the total.
  • Enter a new voltage and frequency to compare. Read the power saved, the relative performance and the energy saved per task, which assumes that the run time is inversely proportional to the frequency.

Example

A chip has an activity factor of 0.25, a switched capacitance of 60 nF, a supply of 1.1 V and a clock of 3.6 GHz. The dynamic power is 0.25 × 60 × 10⁻⁹ × 1.1² × 3.6 × 10⁹ = 65.3 W, and with 12 W of leakage the total is 77.3 W. At 0.95 V and 2.9 GHz, the dynamic power falls to 39.3 W and the total to 51.3 W, a saving of 33.7 % for a performance of 80.6 %. The energy per task falls by 17.7 %.

Why it matters

Power sets the heat to remove, the battery life and the electricity bill. The calculation shows why a small drop in voltage is worth more than a drop in frequency alone, how much an undervolt or a power-saving mode can save, and why chip makers cap the frequency before the temperature does.

Good to know

The model treats the capacitance, the activity and the leakage as fixed, and it assumes that the lower voltage still works at the new frequency, which depends on the chip. Real processors have voltage and frequency curves set by the maker, boost behaviour, shared uncore power and temperature effects on leakage. Use the result as a physics-based estimate.

The computer energy cost calculator prices the power a PC uses, the electricity cost calculator prices any load, the heat sink calculator sizes cooling for the power, and the Ohm’s law calculator relates voltage, current and power.

Frequently asked questions

What is the formula for dynamic power?

The dynamic power of a CMOS circuit is P = α C V² f, where α is the activity factor, C the total switched capacitance, V the supply voltage and f the clock frequency. It comes from charging and discharging the capacitances of the gates and wires once per switching cycle. The voltage enters as a square, so it matters most.

Why does lowering the voltage save so much?

Because the power goes with the square of the voltage, and the voltage must go down with the frequency for the transistors to keep up. Lowering both together, as dynamic voltage and frequency scaling does, makes the power fall roughly with the cube of the frequency. That is why mobile chips run slowly most of the time.

What is the static power?

It is the power lost to leakage currents that flow even when nothing switches. It grows with temperature and with lower threshold voltages, and in modern chips it can be a large share of the total. The calculator keeps it constant for simplicity, but in fact it also falls a little with a lower voltage.

Does lower power mean lower energy per task?

Not always. A slower clock means that the task runs longer, so the leakage is paid over more time. The calculator compares energy per task as power divided by frequency, for a task whose run time is inversely proportional to the frequency. At very low frequencies, leakage dominates and the energy per task rises again.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.