Skip to content
Omnikalc

Crash force calculator: how hard is an impact?

Enter vehicle weight, impact speed and crush distance to estimate the average impact force, the deceleration in g, the duration and the energy absorbed.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Results

Average impact force

255.0 kN

Average deceleration

16.4 g

Within the range seat belts and airbags are built for
Average impact force in pounds-force
57,331 lbf
Duration of the impact
97 ms
Kinetic energy absorbed
194.3 kJ

When a moving vehicle stops against a barrier, its kinetic energy must go somewhere, and it goes into bending metal over a short distance. This crash force calculator uses the work-energy theorem. Enter the vehicle weight, the impact speed and the crush distance to get the average impact force, the deceleration in g, the duration of the impact and the kinetic energy absorbed.

How the calculation works

  • Speed in metres per second = impact speed × the unit factor (1 mph = 0.447 m/s).
  • Kinetic energy = ½ × mass × speed². It is the energy the structure must absorb to stop the vehicle.
  • Average force = mass × speed² ÷ (2 × crush distance). This is the work-energy theorem: the energy is spent over the crush distance.
  • Deceleration in g = speed² ÷ (2 × crush distance × 9.81). Duration = 2 × crush distance ÷ speed, which assumes a constant deceleration.

Example

A 3,500 lb car hits a barrier at 35 mph and the front end crushes 2.5 ft. The mass is 1,588 kg and the speed is 15.65 m/s. The kinetic energy is 194.3 kJ. The average force is 194.3 kJ ÷ 0.762 m = 255 kN, or about 57,300 lbf. The deceleration is 16.4 g and the impact lasts about 97 ms.

Why it matters

The numbers explain why speed limits, seat belts and crumple zones matter. A small change in impact speed has a large effect on force, and a longer crush distance reduces the force on the occupants. Students use the calculation as a standard physics exercise, and it gives drivers a feel for what a few miles per hour mean in a collision.

Good to know

This is a simplified model of a head-on impact with a fixed rigid barrier. It treats the deceleration as constant, which is not true in a real crash, and it ignores rebound, rotation and the time the occupants take to move relative to the cabin. A crash between two moving vehicles is different: the closing speed is not the right input, and the heavier vehicle changes less in speed. The g-load on the occupants depends on how well the belt and airbag couple them to the vehicle. Treat the result as an order of magnitude and never as a safety assessment.

The stopping distance calculator gives the braking distance before a crash, the kinetic energy calculator computes the energy alone and the force calculator applies Newton’s second law.

Frequently asked questions

How do you calculate crash force?

Use the work-energy theorem. The kinetic energy of the vehicle, half the mass times the speed squared, is absorbed over the crush distance, so the average force is the kinetic energy divided by the crush distance.

Why does crush distance matter so much?

The force is inversely proportional to the distance over which the vehicle stops. Doubling the crumple zone halves the average force and the deceleration. This is the reason cars are built to crush in a controlled way.

Does speed matter more than weight?

Yes. The force is proportional to the mass but to the square of the speed. Going from 35 mph to 70 mph with the same crush distance multiplies the average force by four.

Is the result the peak force?

No. It is an average over the crash. Real crashes have peaks that can be two or three times higher, because the stiff parts of the structure, such as the engine and the frame rails, are met late in the crush.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.