Skip to content
Omnikalc

Brake pedal ratio and braking force calculator

Enter the pedal force, pedal ratio, booster, master cylinder bore, caliper piston and rotor dimensions to get the line pressure, the clamping force, the braking force and the deceleration in g.

Updated on
Your inputs
lb

Value out of range

Value out of range

Value out of range

in

Value out of range

in

Value out of range

Value out of range

Value out of range

in

Value out of range

in

Value out of range

%

Value out of range

lb

Value out of range

Results

Brake line pressure

1,164 psi

Clamping force per caliper

2,057 lb

Deceleration

0.53 g

Force on the master cylinder
700 lb
Braking torque per wheel
617 lb·ft
Braking force per front wheel
644 lb
Stopping distance from 60 mph (100 km/h)
228.9 ft

The brake pedal ratio and braking force calculator follows the force of the foot through the pedal lever, the booster and the master cylinder to give the line pressure, the clamping force of the caliper, the braking torque, the deceleration in g and the stopping distance from highway speed.

How the calculation works

  • Enter the pedal force, the pedal ratio, the booster ratio and the master cylinder bore.
  • Enter the caliper piston, the friction coefficient, the rotor and tire radius and the front share of the braking.
  • Enter the vehicle weight and read the pressure, the force, the deceleration and the distance.

Example

A pedal force of 50 lb with a ratio of 4 and a booster of 3.5 puts 700 lb on the master cylinder, which makes 1,164 psi in the lines. Each front caliper clamps with 2,057 lb, which gives 617 lb·ft of braking torque and 644 lb at the road per front wheel. The deceleration is 0.53 g, a stop from 60 mph or 100 km/h in 228.9 ft.

Why it matters

The calculator helps people who upgrade or design brakes for a car, a kart or a trailer, mechanics, builders of kit cars and students, who want to see how the master cylinder, the caliper and the pedal ratio change the pedal feel and the braking force.

Good to know

Use the real dimensions of your parts: the bore of the master cylinder, the total piston area of the caliper and the effective radius of the rotor, measured to the middle of the pad. The friction coefficient depends on the pad, the temperature and the wear. The calculation ignores the losses in the hoses, the stiffness of the system and the pad temperature, and assumes that the rear brakes follow the front. This tool is for understanding and design checks, and not a substitute for a brake system validation and test.

The stopping distance calculator gives a stop from the reaction time, the longitudinal weight transfer calculator shows the axle loads, the brake rotor temperature calculator estimates heating and the hydraulic press calculator handles another hydraulic force.

Frequently asked questions

What does the pedal ratio do?

The brake pedal is a lever. If the pedal pad is four times farther from the pivot than the rod that pushes the master cylinder, the force of the foot is multiplied by four. A higher ratio gives more force for the same effort, but needs more pedal travel. Typical ratios are 4:1 to 6:1 on road cars, with a booster that multiplies the force further.

How is the line pressure computed?

The force on the master cylinder piston, which is the foot force multiplied by the pedal ratio and the booster ratio, divided by the area of the bore, gives the hydraulic pressure in the brake lines. A smaller master cylinder gives more pressure for the same force, but less fluid volume, so more pedal travel. Pressures of 800 to 1,500 psi are common in hard braking.

How does the caliper turn pressure into braking?

The pressure acts on the piston area of the caliper to push the pads against the rotor with a clamping force. Each pad applies friction on one face of the rotor, which gives a braking torque of two times the friction coefficient times the clamping force times the effective radius. Dividing by the tire radius gives the force at the road.

What does the deceleration tell?

The braking force at the front axle is divided by the front share of the braking to estimate the total force, then by the weight to get the deceleration in g. A road car reaches 0.8 to 1.0 g on good tires. The result here assumes the rear brakes are well balanced to the front, and that the tires have enough grip to use the force.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.