Skip to content
Omnikalc

Hill equation calculator: effect, EC10 and EC90 from an EC50 and a slope

Enter the EC50, the Hill coefficient, the maximum and baseline effects and a concentration to get the effect, the concentration for a target effect, EC10 and EC90.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

Value out of range

Value out of range

Results

Effect at this concentration

66.93

Share of the maximum range reached (%)
66.9 %
Concentration for the target effect
62.996
EC10
5.778
EC90
108.169
EC90 ÷ EC10 (steepness of the curve)
18.7

The Hill equation is the standard model of a sigmoid dose-response curve. The EC50 Hill equation calculator takes the EC50, the Hill coefficient, the maximum and baseline effects, a concentration and a target effect, and gives the effect at that concentration, the share of the range reached, the concentration for the target effect, EC10, EC90 and their ratio.

How the calculation works

  • The Hill equation describes a dose-response curve: E = E0 + (Emax − E0) × C^n ÷ (EC50^n + C^n), where C is the concentration, n the Hill coefficient and EC50 the concentration giving half the maximum effect.
  • The share of the range reached is C^n ÷ (EC50^n + C^n). It is 50 % when C equals EC50.
  • To find the concentration for a target effect p (as a fraction of the range), solve the equation: C = EC50 × (p ÷ (1 − p))^(1 ÷ n).
  • EC10 and EC90 use p = 0.1 and 0.9. Their ratio, 81^(1 ÷ n), shows how steep the curve is: a steeper curve (larger n) has a smaller ratio.

Example

A drug has an EC50 of 25, a Hill coefficient of 1.5, an Emax of 100 and no baseline. At a concentration of 40, the share of the range is 40^1.5 ÷ (25^1.5 + 40^1.5) = 253 ÷ 378 = 66.9 %, so the effect is 66.9. To reach 80 % of the maximum, the concentration must be 25 × 4^(1 ÷ 1.5) = 63.0. EC10 is 5.78 and EC90 is 108.2, a ratio of 18.7.

Why it matters

Pharmacologists, toxicologists and biochemists describe potency and steepness with EC50 and the Hill coefficient. The calculator turns those two numbers into predictions at any concentration, which is helpful for planning experiments and reading papers.

Good to know

The Hill equation is an empirical description and not proof of a mechanism. The Hill coefficient does not always equal the number of binding sites. Concentrations should use the same units as the EC50, and the model assumes that the baseline and maximum are known.

The Michaelis-Menten calculator covers enzyme kinetics, and the serial dilution calculator helps prepare the concentrations to test.

Frequently asked questions

What is the EC50?

The EC50 is the concentration of a drug or other agent that produces half of its maximum effect. It is a standard measure of potency, so a lower EC50 means that less of the agent is needed. The IC50 is the same idea for inhibition, the concentration that blocks half of a response.

What does the Hill coefficient tell me?

It describes the steepness of the dose-response curve. A value of 1 gives the simple hyperbolic curve of one-to-one binding. Values above 1 give a steeper, more switch-like curve, often linked to cooperative binding, while values below 1 give a flatter curve.

Why are EC10 and EC90 useful?

They show the range of concentrations over which the response changes. A steep curve goes from 10 to 90 percent over a narrow concentration range, while a shallow one needs a very wide range. This matters for dosing, safety margins and assay design.

Should I fit the curve myself?

To get the EC50 and the Hill coefficient from data, fit the equation to the measured responses with a nonlinear least-squares method in a statistics or plotting program. This calculator then helps you to use the fitted values to predict responses at other concentrations.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.