Skip to content
Omnikalc

Euler buckling calculator: critical load and slenderness

Enter the material, the section, the length and the end conditions to get the Euler critical load, the slenderness ratio and the allowable load.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

MPa

Value out of range

Value out of range

Results

Euler critical load

114.2 kN

Elastic buckling governs: Euler's formula applies
Allowable load with the factor of safety
38.1 kN
Slenderness ratio (KL ÷ radius of gyration)
207.8
Critical stress
45.7 MPa
Moment of inertia of the weak axis
52.1 cm⁴

A long, thin column can fail not by crushing but by buckling, a sudden sideways bend under a compressive load. Euler’s formula gives the critical load at which that happens. This calculator computes it from the material, the section, the length and the end conditions, and shows the slenderness and the allowable load with a factor of safety.

How the calculation works

  • Moment of inertia (rectangle, weak axis) = smaller side³ × larger side ÷ 12
  • Critical load = π² × E × I ÷ (K × L)²
  • Radius of gyration = √(I ÷ area)
  • Slenderness ratio = K × L ÷ radius of gyration
  • Critical stress = critical load ÷ area
  • Allowable load = critical load ÷ factor of safety

Example

A 50 × 50 mm steel column (E = 200 GPa, yield 250 MPa) is 3 m long and pinned at both ends. The moment of inertia is 52.1 cm⁴. The critical load is 114.2 kN and the slenderness ratio 207.8. The critical stress, 45.7 MPa, is well below yield, so Euler’s formula applies. With a factor of safety of 3, the allowable load is 38.1 kN.

Why it matters

Buckling is the failure mode of many props, struts, posts and truss members. The load falls with the square of the length: doubling the length cuts the critical load to a quarter. Making the section stiffer, bracing the middle or fixing an end are the efficient ways to raise it. Using more material in the same shape helps much less than changing its shape.

Good to know

Euler’s formula is valid for slender columns, with a slenderness ratio above about 100 for steel. Short columns fail by yielding and need other formulas. Real columns have bends, load off center and residual stresses, which lower the capacity, so building codes use design curves and safety factors. This tool is for education and does not replace a structural engineer.

The moment of inertia calculator computes sections, the Young’s modulus calculator relates stress and strain, and the section modulus calculator is the next step for beams.

Frequently asked questions

What is Euler buckling?

A slender column under a compressive load can suddenly bend sideways at a load far below the one that would crush the material. Euler's formula gives that critical load from the stiffness of the material, the shape of the section, the length and the end conditions.

What does the effective length factor K mean?

It adjusts the length for how the ends are held. A column pinned at both ends has K = 1. Fixed ends make it stiffer (K = 0.5), and a free end, as in a flagpole, makes it much weaker (K = 2). The load varies with 1 ÷ K².

Why does the weak axis matter?

A column buckles about the axis with the smaller moment of inertia, which is the direction in which it is thinnest. For a rectangle that means the smaller side, which is why a deep, narrow section is a poor column.

When is Euler's formula not valid?

For short, stocky columns, where the stress reaches the yield strength before buckling. The formula also assumes a perfectly straight, centrally loaded column. Real columns have imperfections, so a factor of safety is applied.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.