Skip to content
Omnikalc

Plate buckling critical stress and effective width calculator

Enter the plate width and thickness, the steel properties and the edge supports to get the elastic critical buckling stress, the plate slenderness, the effective width ratio and the effective width.

Updated on
Your inputs
in

Value out of range

in

Value out of range

ksi

Value out of range

Value out of range

ksi

Value out of range

Results

Effective width

9.05 in

Elastic critical buckling stress
45.5 ksi
Width to thickness ratio
48.0
Plate slenderness
1.048
A slender plate: the effective width is smaller than the width
Effective width ratio
0.754

The plate buckling calculator gives the elastic critical stress of a flat plate in compression, the plate slenderness and the effective width by Winter’s method, for different support conditions of its edges.

How the calculation works

  • Enter the width and the thickness of the plate, the modulus, the Poisson’s ratio and the yield strength.
  • Choose the support condition of the two edges parallel to the load, which sets the buckling coefficient k.
  • The calculator gives the critical buckling stress, the slenderness, the effective width ratio and the effective width.

Example

A plate 12 in wide and 0.25 in thick, with both long edges simply supported (k = 4), steel with E = 29,000 ksi and Fy = 50 ksi. The critical stress is 4 × π² × 29,000 / (12 × (1 − 0.3²)) × (0.25 / 12)² = 45.5 ksi. The slenderness is √(50 / 45.5) = 1.048, above 0.673, so the effective width ratio is (1 − 0.22 / 1.048) / 1.048 = 0.754 and the effective width is 9.05 in. If one long edge is free (k = 0.425) and the plate is 4 in wide, the stress is 43.5 ksi and the ratio 0.77.

Why it matters

The calculator helps structural engineers, designers of cold-formed steel, plate girders and tanks, and students to see how the width to thickness ratio and the edge conditions change the buckling stress and how much of a slender plate is effective.

Good to know

Choose the support condition carefully. The edge of a flange outstand or a stiffened lip is free on one side, which gives a low k, while the web of a section is supported at both edges. The width b is the distance between supports, usually between the toes of the fillets or the centerlines of welds. If the buckling stress is far above the yield, the plate is fully effective and the plain yield check is enough. In a built-up member the real behavior depends on the stiffeners, so use the code rules for the final design.

The web shear buckling calculator checks the web of a plate girder, the Euler buckling calculator gives the column buckling load, the wide flange compactness calculator checks the width to thickness limits and the Johnson parabola calculator handles short columns.

Frequently asked questions

What is the critical stress of a plate?

A flat plate loaded in compression in its plane buckles at the stress σcr = k π² E / (12 (1 − ν²)) (t / b)². The coefficient k depends on how the edges are supported: 4 for a long plate with all edges simply supported, up to 6.97 with fixed edges, and as low as 0.425 when one long edge is free. A thinner or wider plate buckles at a much lower stress.

What is the effective width?

A plate that buckles does not fail at once. After buckling, it still carries more load, but the stress concentrates near the supported edges. The effective width method replaces the plate by a narrower one under the full edge stress. Winter's formula gives the width ratio ρ = (1 − 0.22 / λ) / λ, with λ = √(Fy / σcr), when the plate is slender.

When is a plate fully effective?

When the slenderness λ is not more than 0.673 for a plate supported on both edges, or 0.748 for a plate with a free edge, the buckling stress is high enough for the plate to reach yield, and the whole width counts. A stocky plate, as in a thick flange, is usually fully effective.

What does the calculator leave out?

The calculator leaves out the residual stresses, the initial imperfections of the plate, the effect of a stress gradient such as in a web in bending, the stiffeners and the finite length of the plate. It treats a long plate with a uniform compression. Use a design code for members, with the limits of the width to thickness ratio.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.