Skip to content
Omnikalc

Inductors in series and parallel calculator

Enter three inductances, the current and the frequency to get the series total, the parallel total, the reactance and the stored energy.

Updated on
Your inputs
mH

Value out of range

mH

Value out of range

mH

Value out of range

A

Value out of range

Hz

Value out of range

Results

Total inductance in series

79.00 mH

Total inductance in parallel
5.998 mH
Reactance of the series chain
29.78 Ω
Voltage across the series chain
59.6 V
Energy stored in the series chain
0.1580 J

The inductors in series and parallel calculator gives the total inductance in series, the total inductance in parallel, the reactance, the voltage and the stored energy of three coils.

How the calculation works

  • Enter the three inductances in millihenries.
  • Enter the current in the series chain and the frequency.
  • The calculator adds the coils for the series total, combines the reciprocals for the parallel total, then gives the reactance, the voltage and the energy of the series chain.

Example

Three coils of 10 mH, 22 mH and 47 mH give 79.00 mH in series and 5.998 mH in parallel. At 60 Hz the series chain has a reactance of 29.78 Ω. With 2 A flowing, the voltage across it is 59.6 V and it stores 0.1580 J.

Why it matters

The calculator helps electronics students, hobbyists and designers who combine chokes, filter coils and winding sections, check a stock of standard values against a target inductance, or estimate the voltage a coil develops at a given frequency.

Good to know

The formulas assume that the coils do not couple magnetically. Coils placed close to each other, on the same core or inside a shield, share flux and the true total differs, so use the coupled coils calculator for that case. Real inductors also have winding resistance, a self-resonant frequency above which they act as capacitors, and a saturation current beyond which the inductance falls. Check these limits on the data sheet before you put coils in series or in parallel, and share the current among parallel coils only if their resistances are close, since the lower resistance carries more of it.

The solenoid inductance calculator gives the inductance of one coil from its winding, the RL circuit calculator gives the time constant with a resistor, the LC resonance calculator gives the frequency with a capacitor and the capacitors calculator combines capacitors the same way.

Frequently asked questions

How do inductors add in series?

Inductors in series add like resistors in series: L total = L1 + L2 + L3. The same current flows through every coil, so the voltages add. This holds only when the coils do not share a magnetic field. Coils wound close together or on the same core are coupled, and the mutual inductance adds to or takes away from the total.

How do inductors combine in parallel?

In parallel the reciprocals add: 1 / L total = 1 / L1 + 1 / L2 + 1 / L3. The total is always smaller than the smallest coil, as with resistors in parallel. Two coils of the same value in parallel give half of that value. Again the rule assumes no coupling between the coils.

What is the reactance of an inductor?

The inductive reactance is X = 2 × π × f × L, in ohms. It grows with the frequency and with the inductance, so a coil passes direct current easily and blocks high frequencies. The voltage across a coil equals the current times the reactance, and it leads the current by 90 degrees in an ideal coil.

Where does the energy of a coil sit?

A coil stores energy in its magnetic field: E = ½ × L × I². The energy depends on the square of the current, so doubling the current multiplies the energy by four. The energy is released when the current falls, which is why an inductor needs a freewheel diode or a snubber when a switch opens.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.