Skip to content
Omnikalc

Langmuir isotherm calculator: how much gas is adsorbed?

Enter the monolayer capacity, the Langmuir constant K and the pressure to get the surface coverage, the amount adsorbed and the half-coverage pressure.

Updated on
Your inputs
mmol/g

Value out of range

1/bar

Value out of range

Value out of range

Results

Surface coverage

70.6%

More than half the sites are occupied
Amount adsorbed
1.765 mmol/g
Pressure for half coverage (1 ÷ K)
1.250 bar
Pressure for 90 % coverage (9 ÷ K)
11.25 bar
Initial slope at low pressure (K × capacity)
2.000 mmol/(g·bar)

How much gas sticks to the surface of activated carbon, a catalyst or a membrane? The Langmuir isotherm answers for the simplest case: a single layer of molecules on a fixed number of sites. This calculator gives the surface coverage and the amount adsorbed at a given pressure, with the pressures for half and 90 % coverage.

How the calculation works

  • Coverage θ = K × P ÷ (1 + K × P)
  • Amount adsorbed q = capacity × θ
  • Half coverage at P = 1 ÷ K
  • 90 % coverage at P = 9 ÷ K
  • Initial slope at low pressure = K × capacity (Henry’s law region)

K is in inverse bars, so the pressure must be in bars.

Example

A carbon adsorbs up to 2.5 mmol/g of a gas, with K = 0.8 bar⁻¹. At 3 bar, the coverage is 2.4 ÷ 3.4 = 70.6 % and the amount adsorbed is 1.765 mmol/g. Half coverage needs 1.25 bar, 90 % needs 11.25 bar, and the initial slope is 2.0 mmol/(g·bar). Raising the pressure from 3 to 6 bar adds only 17 % to the amount adsorbed.

Why it matters

The isotherm is used to design gas storage on porous materials, air purification, catalysis, chromatography and gas sensors. It shows the law of diminishing returns of adsorption: the first increments of pressure fill the surface quickly, and the last ones add little. It also gives the pressures at which an adsorption bed should be regenerated.

Good to know

The constants depend on the temperature, and K usually falls as the temperature rises, so a bed adsorbs less when it is hot. Real surfaces have sites of different strengths, so fit the model over a modest pressure range. The model also applies to adsorption from a solution, with the concentration in place of the pressure. This tool is for education.

In practice

Try lowering K from 0.8 to 0.1 bar⁻¹ to represent the same material at a higher temperature: the surface needs about eight times more pressure to reach the same coverage. This is the principle of temperature swing adsorption, where a bed adsorbs a gas when cold and releases it when heated, used in air drying and carbon capture.

The ideal gas calculator links pressure, volume and temperature, the partial pressure calculator handles gas mixtures, and the Henry’s law calculator treats gas dissolved in a liquid.

Frequently asked questions

What is the Langmuir isotherm?

It describes how much gas sticks to a surface at a given pressure and constant temperature, assuming a single layer of molecules, a fixed number of identical sites and no interaction between neighbors. The coverage is θ = K·P ÷ (1 + K·P).

What do the constants mean?

The capacity is the amount adsorbed when the surface is full. K measures how strongly the gas binds: a large K means the surface fills at low pressure. K falls when the temperature rises.

When does the model fail?

When molecules form several layers, when the sites differ or when adsorbed molecules attract or repel each other. For multilayer adsorption the BET model is used, and for uneven surfaces the Freundlich model.

How do I get K and the capacity from experiments?

Measure the amount adsorbed at several pressures and plot P ÷ q against P. For a Langmuir system this is a straight line, with a slope of 1 ÷ capacity and an intercept of 1 ÷ (K × capacity).

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.