Skip to content
Omnikalc

Freundlich adsorption isotherm calculator

Enter the Freundlich constants, the equilibrium and starting concentrations and the volume to get the adsorbed amount, the dose of adsorbent and the removal.

Updated on
Your inputs
mg/g

Value out of range

Value out of range

mg/L

Value out of range

mg/L

Value out of range

L

Value out of range

Results

Adsorbed amount at equilibrium

15.81 mg/g

Mass of adsorbent needed
2.53 g
Dose per litre
2.53 g/L
Removal
80.0 %
Capacity in equilibrium with the starting solution
35.36 mg/g
Mass of adsorbent for 95 % removal
6.01 g
Heterogeneity factor 1/n
0.500

The Freundlich isotherm calculator gives the amount adsorbed at equilibrium, the mass of adsorbent and the dose per litre for a target concentration, the removal, the capacity with the starting solution, the mass for 95 % removal and the heterogeneity factor.

How the calculation works

  • Enter the Freundlich constants Kf and n of your adsorbent and pollutant.
  • Enter the starting concentration, the concentration to reach and the volume to treat.
  • The calculator applies the isotherm and a mass balance for the batch.

Example

With a constant of 5 mg/g and an exponent of 2, a solution at 10 mg/L holds 15.81 mg/g on the adsorbent. Treating 1 L from 50 mg/L takes 2.53 g, a dose of 2.53 g/L for a removal of 80.0 %. For 95 % removal the mass rises to 6.01 g. The capacity in equilibrium with the starting solution is 35.36 mg/g.

Why it matters

The calculator helps environmental engineers, water treatment operators, chemistry students and aquarium keepers who use activated carbon, resins or clays to remove a pollutant, a dye, a metal or a taste from water, and who need to estimate the amount of adsorbent.

Good to know

The isotherm gives the equilibrium state for a single batch, so a column in continuous flow needs less adsorbent per volume than a batch of the same removal. Kf and n depend on the adsorbent, the compound, the temperature and the pH, so use values measured in conditions close to yours. Do not extrapolate far outside the concentration range of the tests, since the Freundlich model has no saturation limit. Competing compounds in real water lower the capacity, often by a factor of two or more, so add a safety margin and confirm with a jar test.

The Langmuir isotherm calculator treats adsorption with a saturation limit, the reverse osmosis calculator handles another way of removing dissolved compounds, the partial pressure calculator is used for gas adsorption and the osmotic pressure calculator deals with dissolved species.

Frequently asked questions

What is the Freundlich isotherm?

The Freundlich isotherm is an empirical relation between the amount adsorbed per gram of adsorbent, q, and the concentration left in solution at equilibrium, C: q = Kf × C^(1/n). The constant Kf is a measure of the capacity and n of the intensity of adsorption. It applies to heterogeneous surfaces, like activated carbon, in a limited concentration range.

How do I interpret the exponent n?

A value of n above 1, so that 1/n is under 1, means favorable adsorption: the capacity rises less than in proportion to the concentration, and a good removal is possible even at low levels. A value of n near 1 is a linear isotherm, and n below 1 is unfavorable. Typical values for organic compounds on activated carbon are 1.5 to 5.

How is the dose of adsorbent calculated?

A mass balance gives m = (C0 − C) × V / q, where C0 is the starting concentration, C the final one, V the volume and q the amount adsorbed at the final concentration. For a batch of 1 L from 50 to 10 mg/L with Kf = 5 and n = 2, q = 15.8 mg/g and the dose is 2.53 g.

How do I find Kf and n?

Run batch tests with different doses, measure the final concentrations, and plot log q against log C. The slope is 1/n and the intercept is log Kf. Use the same temperature and pH as in your process, and units that are consistent with the way you apply the constants: Kf has units of (mg/g) / (mg/L)^(1/n).

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.