Skip to content
Omnikalc

Lineweaver–Burk plot calculator: find Vmax and Km from four measurements

Enter four substrate concentrations and reaction rates to fit the double reciprocal plot and get Vmax, Km, the line parameters and the R² of the fit.

Updated on
Your inputs
mM

Value out of range

µmol/min

Value out of range

mM

Value out of range

µmol/min

Value out of range

mM

Value out of range

µmol/min

Value out of range

mM

Value out of range

µmol/min

Value out of range

Results

Maximum rate Vmax

99.60 µmol/min

Michaelis constant Km
4.96 mM
Slope of the line (Km ÷ Vmax)
0.0498
Intercept on the 1/v axis (1 ÷ Vmax)
0.01004
Intercept on the 1/[S] axis (−1 ÷ Km)
-0.2015
Coefficient of determination R²
0.9999
A good straight line: the data follow Michaelis–Menten kinetics

The Lineweaver–Burk plot turns the curve of an enzyme reaction into a straight line. This Lineweaver–Burk plot calculator takes four substrate concentrations and reaction rates, fits the double reciprocal line and gives Vmax, Km, the slope, the intercepts and the R² of the fit.

How the calculation works

  • Enter four pairs of substrate concentration [S] and reaction rate v measured for the enzyme.
  • The calculator plots 1/v against 1/[S] and fits a straight line by least squares.
  • The y-intercept is 1/Vmax and the slope is Km/Vmax, so Vmax = 1 / intercept and Km = slope / intercept.
  • It also gives the x-intercept (−1/Km) and the R² of the fit.

Example

An enzyme gives rates of 28.6, 50.2, 66.0 and 83.5 µmol/min at 2, 5, 10 and 25 mM of substrate. The line of 1/v against 1/[S] has a slope of 0.0498 and an intercept of 0.01004. So Vmax = 99.6 µmol/min, Km = 4.96 mM and R² = 0.9999.

Why it matters

The plot is a classic exercise in biochemistry and enzymology courses, and it is also used to show the type of enzyme inhibition at a glance. The calculator saves the work of taking reciprocals and fitting by hand, and it lets students check their results.

Good to know

The method uses a least squares line on the reciprocals, which gives a large weight to the points at low concentration. For research work, a direct non-linear fit of the Michaelis–Menten equation is more reliable. Use initial rates measured with a small consumption of substrate, at a constant temperature and pH, and with at least four concentrations that go from below to above Km. A concentration range from about Km/3 to 5 Km gives the most reliable values, and a low R² often points to a pipetting error, substrate inhibition, a product that slows the reaction or a reaction that was not measured at its initial rate.

The Michaelis–Menten calculator gives the rate from Vmax and Km, the enzyme activity calculator covers activity units, the linear regression calculator covers the least squares method, and the R-squared calculator covers the quality of a fit.

Frequently asked questions

What is a Lineweaver–Burk plot?

It is a graph of 1/v against 1/[S] for an enzyme reaction. Taking the reciprocal of the Michaelis–Menten equation, v = Vmax [S] / (Km + [S]), gives 1/v = (Km / Vmax)(1/[S]) + 1/Vmax, which is a straight line. It is also called the double reciprocal plot, and it was proposed by Hans Lineweaver and Dean Burk in 1934.

How do I read Vmax and Km from the line?

The line crosses the vertical axis at 1/Vmax and the horizontal axis at −1/Km. The slope is Km/Vmax. A line fitted to the data gives these three values in one step. The calculator reads them out as Vmax and Km, with the units of your data.

What are the weaknesses of the method?

The reciprocal gives a large weight to the points at low substrate concentration, which have the largest relative error, and compresses the points at high concentration. The estimates of Vmax and Km can be biased as a result. Non-linear fitting of the original equation, or the Eadie–Hofstee and Hanes–Woolf plots, are better, and the double reciprocal plot is mainly good for display.

How can the plot show inhibition?

Competitive inhibitors change the slope and keep the y-intercept (Vmax is the same, apparent Km is larger). Non-competitive inhibitors keep the x-intercept and raise the y-intercept (Vmax falls). Uncompetitive inhibitors give parallel lines. Comparing the lines with and without inhibitor shows the type.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.