Skip to content
Omnikalc

Minimum fluidization velocity calculator: at what gas speed does a bed start to flow like a liquid?

Enter the particle size and density and the gas properties to get the minimum fluidization velocity, the Archimedes number and the pressure drop with the Wen–Yu correlation.

Updated on
Your inputs
mm

Value out of range

lb/ft³

Value out of range

lb/ft³

Value out of range

cP

Value out of range

Results

Minimum fluidization velocity

0.238 ft/s

Archimedes number
2,452
Reynolds number at minimum fluidization
1.45
Pressure drop per foot of bed at fluidization
0.596 psi/ft

A fixed bed of powder can be turned into something that flows like a liquid by blowing gas up through it at the right speed. The minimum fluidization velocity calculator takes the particle diameter, the particle density and the gas density and viscosity, and gives the minimum fluidization velocity, the Archimedes number, the Reynolds number at that point and the pressure drop per foot of bed.

How the calculation works

  • Enter the particle diameter, the particle density, and the density and viscosity of the gas, usually air at the temperature of the process.
  • The calculator finds the Archimedes number Ar = ρg (ρp − ρg) g d³ / μ², the ratio of buoyancy and gravity forces to viscous forces.
  • It then uses the correlation of Wen and Yu (1966): Re_mf = √(33.7² + 0.0408 Ar) − 33.7, and the minimum fluidization velocity u_mf = Re_mf × μ / (ρg d).
  • It also gives the pressure drop per foot of bed at that point, which equals the weight of the bed per unit area, for a void fraction of about 0.45.

Example

A bed of sand with a particle size of 0.3 mm and a density of 156 lb/ft³ (2,500 kg/m³) is fluidised with air of density 0.075 lb/ft³ and viscosity 0.018 cP. The Archimedes number is 2,450, so Re_mf = √(33.7² + 0.0408 × 2,450) − 33.7 = 1.45. The minimum fluidization velocity is 0.238 ft/s (7.3 cm/s), and the pressure drop at that point is about 0.6 psi per foot of bed.

Why it matters

The minimum fluidization velocity is the first number needed to design a fluidised bed: it fixes the lowest flow of gas for operation and the size of the blower. Chemical, mineral and food engineers use it for reactors, dryers and coolers, and the calculator makes it easy to see the effect of the particle size, the density and the temperature of the gas.

Good to know

The Wen–Yu correlation is a general estimate for spherical or nearly spherical particles of narrow size, in gas–solid beds at moderate pressure, with an accuracy of about ±30 %. The void fraction at minimum fluidization is taken as 0.45 for the pressure drop, and it is 0.4 to 0.5 in practice. Fine, sticky or wide-size powders, and operation at high pressure, need a measurement. Use the result as a first estimate.

The Reynolds number calculator characterises the flow, the terminal velocity calculator gives the speed at which a particle falls in a fluid, the residence time calculator covers the time in a vessel, and the air density calculator gives the density of the gas.

Frequently asked questions

What is fluidization?

When a gas flows up through a bed of fine particles at a high enough speed, the drag force on the particles balances their weight, and the bed expands and behaves like a boiling liquid. The particles are well mixed, and the heat and mass transfer are excellent. Fluidised beds are used in catalytic cracking of oil, coal combustion, drying, granulation and in the coating of tablets.

What is the minimum fluidization velocity?

It is the superficial gas velocity at which the pressure drop across the bed equals the weight of the bed per unit area, and the bed starts to float. Below it the bed stays fixed, and the pressure drop follows the Ergun equation. Above it, the pressure drop stays nearly constant, while the bed expands and bubbles form. The operating velocity is generally 2 to 10 times u_mf.

What are the limits of the Wen–Yu correlation?

It is an empirical fit to many sets of data for gas–solid beds, with an error of about 30 %, which is good for a first estimate. For fine powders of Geldart group C that stick together, for large temperatures and pressures, and for particles with a wide range of sizes, the real value differs, and a test in a small column is the best way to know.

What is the Archimedes number?

It is a dimensionless number that compares the gravity and buoyancy forces on a particle in a fluid with the viscous forces, Ar = ρf (ρp − ρf) g d³ / μ². A high value, as for large and heavy particles, means that inertia dominates and the particles need a strong flow to be lifted. It is used for the fluidization and the sedimentation of particles.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.