Skip to content
Omnikalc

ND filter calculator: how long should the exposure be?

Enter your metered shutter speed and the strength of your ND filter to get the new exposure time for long-exposure photos of water, clouds and crowds.

Updated on
Your inputs

Value out of range

Value out of range

Results

Shutter speed with the filter (seconds)

8.2 s

Use a tripod: this is too slow to hold by hand
Same exposure time in minutes
0.14 min
Light reduction factor (× darker)
1,024
Optical density
3.0
Total stops to compensate
10.0 stops

A neutral density (ND) filter is a piece of dark glass that cuts the light reaching your sensor without changing the colors. Photographers use one to slow the shutter in bright light: to blur a waterfall, smooth the sea, remove people from a street scene, or keep a wide aperture for a shallow depth of field in the sun. The calculation is simple but easy to get wrong with a strong filter, so this tool does it for you.

How the calculation works

Each stop of filter halves the light, so the exposure time must double to compensate:

  • New exposure time = original exposure time × 2^(stops of the filter + extra stops)
  • Light reduction factor = 2^stops (for example ND1000 ≈ 2^10)
  • Optical density = stops × 0.301

Meter the scene without the filter, in aperture priority or manual mode, then read the shutter speed. Enter it as 1 / … of a second, choose the filter, and the calculator returns the longer time to set. Keep the same aperture and ISO.

Example

Without the filter your meter reads 1/125 s at f/8. With a 10-stop filter (ND1000, density 3.0), the exposure becomes 2^10 ÷ 125 = 8.2 seconds, which is 0.14 minutes. Add a polarizer (about 1.5 stops) and it becomes 2^11.5 ÷ 125 = 23 seconds.

Why it matters

Strong filters turn the viewfinder dark, so metering must be done without the filter or with the live view image brightened. Long exposure times also require a sturdy tripod, a remote release or a self-timer, and a camera strap closed to keep wind from shaking it. Beyond 30 seconds many cameras switch to a bulb mode with a manual timer.

Good to know

Some ND filters are not perfectly neutral and can add a warm or cool cast: shoot raw and correct white balance. Variable ND filters are convenient but can show a dark cross pattern at their maximum strength on wide lenses. Light can also leak in through the viewfinder during long exposures: close the eyepiece shutter or cover it. This tool is for education.

The exposure value calculator links aperture, shutter and ISO, the depth of field calculator shows the effect of the aperture, and the astrophotography exposure calculator gives the longest exposure before stars trail.

Frequently asked questions

How do I work out the new shutter speed with an ND filter?

Multiply the metered exposure time by 2 for each stop of filter. A 10-stop filter multiplies the time by 1,024: 1/125 s becomes about 8 seconds. Keep aperture and ISO the same and change only the shutter speed.

What do ND8, 0.9 and 3 stops mean?

They are three ways of naming the same filter. ND8 is the factor of light reduction (8 times darker), 0.9 is the optical density (each 0.3 is one stop) and 3 stops is the number of times the exposure is halved.

Why do very long exposures need extra time?

At exposures of about a second or longer, film and digital sensors respond less than expected to the light (reciprocity failure on film). Add a stop or two for film; with digital cameras, the effect is usually small, but a long exposure also adds heat noise.

Can I stack two ND filters?

Yes. Stops add up, so ND8 (3 stops) with ND64 (6 stops) gives 9 stops. Stacking can cause color casts, vignetting with wide lenses and extra reflections, so a single filter is usually cleaner.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.