Skip to content
Omnikalc

PEM fuel cell stack calculator: power, hydrogen consumption and heat from cells, area and current

Enter the number of cells, their area, current density and cell voltage to get the stack power, the hydrogen consumption, the efficiency, the air flow and the heat to remove.

Updated on
Your inputs

Value out of range

cm²

Value out of range

A/cm²

Value out of range

V

Value out of range

Value out of range

Results

Electric power of the stack

7.80 kW

Efficiency on the lower heating value

51.9%

Hydrogen use

0.451 kg/h

Stack voltage
65.0 V
Stack current
120 A
Electricity produced per kg of hydrogen
17.3 kWh/kg
Waste heat to remove
7.24 kW
Air flow at normal conditions
398 L/min
Water produced
4.03 kg/h

A proton-exchange membrane (PEM) fuel cell turns hydrogen and oxygen into electricity, water and heat. One cell gives less than one volt, so cells are stacked in series. This calculator takes the number of cells, their area, the current density and the cell voltage read on a polarization curve, and returns the power, the hydrogen consumption, the efficiency, the air flow and the heat to evacuate.

How the calculation works

  • Stack current = current density × cell area
  • Stack voltage = number of cells × cell voltage
  • Power = stack voltage × stack current
  • Hydrogen use = N × I ÷ (2F), with F = 96,485 C/mol, then × 2.016 g/mol
  • Oxygen use = N × I ÷ (4F); air = stoichiometry × oxygen ÷ 0.21
  • Efficiency (LHV) = cell voltage ÷ 1.253 V
  • Waste heat = N × I × (1.253 − cell voltage)

Example

A stack of 100 cells of 200 cm² at 0.6 A/cm² carries 120 A. With 0.65 V per cell, the stack voltage is 65.0 V and the power is 7.80 kW. It consumes 0.451 kg of hydrogen an hour, and each kilogram gives 17.3 kWh of electricity, an efficiency of 51.9 % on the lower heating value (33.3 kWh/kg). It produces 4.03 kg of water per hour and 7.24 kW of heat, which a cooling circuit must remove. The air flow at a stoichiometry of 2 is 398 L/min.

Why it matters

The voltage per cell sets the trade-off between efficiency and power. Lower voltage means higher current and more power from the same stack, but more heat and more hydrogen per kWh. Designers pick the operating point from the polarization curve: at low current the cell is efficient and the stack is large, and at high current it is compact and wasteful. The heat output is nearly as large as the electric output, so thermal management is as important as the stack.

Good to know

The 1.253 V reference corresponds to the lower heating value of hydrogen; on the higher heating value the reference is 1.48 V. The tool does not include the power used by compressors, humidifiers and pumps, which can take 10 to 25 % of the output. Voltage depends on temperature, pressure and humidity, and it declines with age. The air flow uses 22.414 L/mol at normal conditions, so the real volume at the operating pressure will be different.

In practice

Use the calculator for a first design: choose the target power and cell voltage, then scale the cells and the area. For hydrogen supply, multiply the consumption by the running hours. The tool is for sizing and education, not a safety design.

Frequently asked questions

How much hydrogen does a fuel cell use?

Faraday's law gives 0.0104 g of hydrogen per ampere per hour for each cell. For the default stack, that is 0.451 kg per hour.

What is the efficiency of a PEM fuel cell?

On the lower heating value, it is the cell voltage divided by 1.253 V. At 0.65 V, it is 51.9 %. Whole systems with auxiliaries are 5 to 10 points lower.

Why does the stack make so much heat?

The part of the hydrogen energy that is not converted to electricity becomes heat. At 0.65 V per cell, about half of the energy is released as heat, which must be cooled away to keep the membrane at about 80 °C.

What is air stoichiometry?

It is the ratio between the oxygen supplied and the oxygen consumed. A ratio above 1 keeps the oxygen concentration up in the cell and removes the water produced.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.